| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: HIDP: reject frames without a transaction header
hidp_recv_ctrl_frame() and hidp_recv_intr_frame() read skb->data[0]
before checking that the L2CAP SDU contains a transaction header. A
connected HIDP peer can send an empty basic-mode SDU and make both paths
use an uninitialized byte from skb tailroom.
KMSAN reports the use in hidp_session_run(), with the uninitialized value
originating in __alloc_skb() through vhci_write(). The control path
produces two reports and the interrupt path produces one.
The byte can also be controlled by a malformed lower-layer packet. If an
HCI ACL packet contains an L2CAP PDU with a declared zero-length payload
followed by an extra 0x15 byte, l2cap_recv_acldata() reduces skb->len to
the declared PDU length before dispatch. The current HIDP path nevertheless
consumes the extra byte as HIDP_TRANS_HID_CONTROL |
HIDP_CTRL_VIRTUAL_CABLE_UNPLUG and terminates the HIDP session. With this
change, the same packet is discarded and a subsequent feature report
request succeeds.
Pull the transaction header with skb_pull_data() and discard frames that
do not contain it. |
| In the Linux kernel, the following vulnerability has been resolved:
veth: convert frag_list skbs before running XDP
A frag_list skb can reach veth with data_len set but nr_frags zero.
veth_convert_skb_to_xdp_buff() only converts skbs that are shared,
locked, have frags[], or do not have enough headroom. It later uses
skb_is_nonlinear() to decide whether to set XDP_FLAGS_HAS_FRAGS and
xdp_frags_size.
That exposes frag_list data to XDP as if it were stored in frags[], but
frags[] is empty. AF_XDP copy mode can then trust the bogus XDP fragment
metadata, walk an empty fragment entry, and crash in memcpy() from
__xsk_rcv().
Route non-linear skbs through skb_pp_cow_data() before exposing them to
XDP, and only advertise XDP frags when the resulting skb has frags[].
skb_copy_bits() already handles frag_list input, and skb_pp_cow_data()
builds frags[] output with skb_add_rx_frag(), which is the
representation XDP multi-buffer expects. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() for transmit path header pulls
In vxlan_xmit(), arp_reduce(), and vxlan_mdb_entry_skb_get(), pskb_may_pull() was
being called to verify the availability of network layer headers (ARP, IPv6/ND,
IP/IPv6 MDB keys).
However, during transmit skb->data points to the MAC header, so skb_network_offset(skb)
is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, len) only checks len bytes from skb->data
rather than skb_network_offset(skb) + len, which can leave part of the network header
in non-linear frags.
Replace these remaining pskb_may_pull() calls with pskb_network_may_pull() to properly
account for the MAC header offset. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/perf_cpum_cf: Add missing array_index_nospec() to __hw_perf_event_init()
ev variable is userspace controlled via event->attr.config and used
as an array index after bounds checking, but without speculation
barriers.
Add the missing array_index_nospec() call to prevent speculative
execution. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Bound PR-OUT TransportID parsing to the received buffer
core_scsi3_decode_spec_i_port() and core_scsi3_emulate_register_and_move()
hand the raw PERSISTENT RESERVE OUT parameter buffer to
target_parse_pr_out_transport_id() without telling it how many bytes are
valid. For an iSCSI TransportID (FORMAT CODE 01b),
iscsi_parse_pr_out_transport_id() locates the ",i,0x" ISID separator with
an unbounded strstr() (and on the error path prints the name with a further
unbounded "%s"). An initiator can submit a TransportID whose iSCSI name
contains neither a ",i,0x" substring nor a NUL terminator, filling the
parameter list to its end, so the scan runs off the end of the buffer.
When the parameter list spans more than one page the buffer is a multi-page
vmap (transport_kmap_data_sg()), so the over-read walks into the trailing
vmalloc guard page and oopses (KASAN: vmalloc-out-of-bounds in strstr). It
is reachable by any fabric that delivers a PR OUT to a device exported
through an iSCSI TPG, including a guest via vhost-scsi.
Pass the number of received bytes down to the parser and validate the iSCSI
TransportID's own self-described length (ADDITIONAL LENGTH + 4) once, up
front: reject it if it is below the spc4r17 minimum or larger than the
received buffer, then bound the separator search, the ISID walk and the
name copy by that length. This is the length check the callers already
perform after the parse (core_scsi3_decode_spec_i_port() compares tid_len
against tpdl, core_scsi3_emulate_register_and_move() validates it against
data_length), moved ahead of the scan. Also drop the unbounded "%s" of the
unterminated name.
Add per-format explicit name-length checks before copying into i_str,
rather than silently truncating with min_t: for FORMAT CODE 00b reject if
the descriptor body (tid_len - 4 bytes) cannot fit in
i_str[TRANSPORT_IQN_LEN]; for FORMAT CODE 01b reject if the name portion
(from &buf[4] up to the separator) cannot fit. Both checks make the bounds
intent explicit at each format branch.
While here, also reject a FORMAT CODE 01b TransportID whose ",i,0x"
separator sits at the very end of the descriptor: that leaves an empty ISID
and points the returned port nexus pointer at buf + tid_len, one past the
descriptor, which the registration code (__core_scsi3_locate_pr_reg(),
__core_scsi3_alloc_registration()) then dereferences as the ISID string --
the same over-read of the parameter buffer for a malformed descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: Validate the packet length reported by the NIC
Validate the packet length reported in the RX CQE before passing it
to skb processing. The CQE is supplied by the NIC device and should
not be blindly trusted. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate minimum PDU size for transform requests
The receive path applies the minimum SMB2 PDU size check only when
ProtocolId is SMB2_PROTO_NUMBER. A packet carrying
SMB2_TRANSFORM_PROTO_NUM bypasses the check even when the negotiated
dialect does not provide transform handling.
On an SMB 2.1 connection, a short transform packet therefore reaches
init_smb2_rsp_hdr(), which interprets the request as a full SMB2 header
and reads beyond the request allocation. The copied fields can then be
returned to the unauthenticated client.
Compression transforms are converted to ordinary SMB2 messages before
protocol validation. After that conversion, validate ordinary SMB2
requests against SMB2_MIN_SUPPORTED_PDU_SIZE and require encryption
transform requests to contain both a transform header and an SMB2
header. This rejects truncated requests before work allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/dp/mst: fix OOB reads in remote DPCD/I2C sideband reply parsers
drm_dp_sideband_parse_remote_dpcd_read() reads num_bytes from the raw
message and then unconditionally does:
memcpy(bytes, &raw->msg[idx], num_bytes);
without checking that idx + num_bytes <= raw->curlen. raw->msg[] is
256 bytes; if a malicious or misbehaving MST hub sets num_bytes larger
than the remaining payload, the memcpy reads past the received data
into whatever follows in raw->msg[].
drm_dp_sideband_parse_remote_i2c_read_ack() has the same flaw (noted
with a /* TODO check */ comment since the code was introduced).
Fix both functions by using a single combined check
(idx + num_bytes > curlen) before each memcpy. Since num_bytes is u8,
it is always >= 0, so this strictly subsumes the simpler idx > curlen
form and no separate step is needed.
[added missing fixes tag] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/dp/mst: fix OOB reads on 2-byte fields in sideband reply parsers
Three sideband reply parsers read 16-bit fields as:
val = (raw->msg[idx] << 8) | (raw->msg[idx+1]);
and check bounds only after the fact. When idx == raw->curlen,
raw->msg[idx+1] reads one byte past the received message data into
the following struct fields (curchunk_len, curchunk_idx, curlen).
Affected functions:
- drm_dp_sideband_parse_enum_path_resources_ack()
full_payload_bw_number and avail_payload_bw_number fields
- drm_dp_sideband_parse_allocate_payload_ack()
allocated_pbn field
- drm_dp_sideband_parse_query_payload_ack()
allocated_pbn field
Fix by using a single combined check (idx + 2 > curlen) before each
2-byte read. Since the check is strictly tighter than idx > curlen,
no separate step is needed.
[added fixes tag] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: bound EDID block reads to the response buffer
virtio_get_edid_block() validates the read offset only against the
device-supplied resp->size field, never against the fixed-size resp->edid
array. The EDID block index is driven by the device-supplied extension
count, so a malicious virtio-gpu backend can advertise a large size
together with a high block count and read far past the array into adjacent
kernel memory, which is then surfaced in the parsed EDID (an out-of-bounds
read / info leak).
Also reject any read whose end exceeds the size of the edid array.
Conforming EDID responses stay within the array and are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate num_subauth when copying ACE in set_ntacl_dacl
set_ntacl_dacl() copies each ACE from the attacker-controlled stored
security descriptor verbatim into the response DACL without checking
sid.num_subauth. The ACE bytes (including an unchecked num_subauth)
originate from an authenticated SMB2_SET_INFO(SecInfo=DACL) that is
stored raw via ksmbd_vfs_set_sd_xattr(); parse_dacl() rejects a bad ACE
with `break` rather than an error, so parse_sec_desc() still returns
success and the malformed SD reaches the xattr intact.
On a subsequent SMB2_QUERY_INFO(SecInfo=DACL) for an inode carrying a
POSIX access ACL, build_sec_desc() -> set_ntacl_dacl() ->
set_posix_acl_entries_dacl() walks the copied ACEs and reads
ntace->sid.sub_auth[ntace->sid.num_subauth - 1]
with num_subauth taken straight from the stored SD. Since sub_auth[]
is fixed at SID_MAX_SUB_AUTHORITIES (15), a crafted num_subauth (e.g.
255) drives an out-of-bounds heap read of ~1 KB with an offset fully
controlled by an authenticated client.
The sibling functions already gate this field:
parse_dacl() -- num_subauth == 0 || > SID_MAX_SUB_AUTHORITIES
parse_sid() -- num_subauth > SID_MAX_SUB_AUTHORITIES
smb_copy_sid() -- min_t(u8, num_subauth, SID_MAX_SUB_AUTHORITIES)
set_ntacl_dacl() is the lone inconsistent path that omits the check.
Add the same num_subauth validation in set_ntacl_dacl() before copying
the ACE, matching the gate already enforced by parse_dacl(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: restore DACL size on check_add_overflow() to avoid malformed ACL
check_add_overflow() unconditionally writes the truncated sum into *d
even on overflow, per its contract in include/linux/overflow.h.
The four check_add_overflow() guards in set_posix_acl_entries_dacl()
and set_ntacl_dacl() break out of the ACE-building loops on overflow,
but the truncated *size is then consumed downstream at the end of
set_ntacl_dacl():
pndacl->size = cpu_to_le16(le16_to_cpu(pndacl->size) + size);
This produces an on-wire NT ACL whose pndacl->size under-reports the
bytes actually written by the preceding fill_ace_for_sid()/memcpy()
calls, yielding a malformed ACL that can trigger out-of-bounds reads
when re-parsed by clients or ksmbd itself.
Restore *size to its pre-addition value on each overflow branch (via
`*size -= ace_sz` / `size -= nt_ace_size`) so that after the break,
*size once again holds the cumulative size of the successfully-written
ACEs. The committed ACL is then truncated-but-self-consistent rather
than malformed.
The ksmbd DACL builders are the only check_add_overflow() sites found
where an overflow path breaks out of a loop and the destination value
is consumed afterward. The other nearby break-style cases either
return -EINVAL on overflow (transport_ipc.c) or break without
consuming the overflowed destination value afterward (buildid.c). |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs-srv: Bound RDMA-Write length to chunk size in rdma_write_sg
When the server answers an RTRS READ, rdma_write_sg() builds the source
scatter/gather entry for the IB_WR_RDMA_WRITE that returns data to the
peer. Its length is taken directly from the wire descriptor:
plist->length = le32_to_cpu(id->rd_msg->desc[0].len);
rd_msg points into the chunk buffer that the remote peer filled via
RDMA-WRITE-WITH-IMM (rtrs_srv_rdma_done() -> process_io_req() ->
process_read()), so desc[0].len is attacker-controlled and, before this
change, was only rejected when zero. The source address is the fixed
chunk start (dma_addr[msg_id]) and the source lkey is the PD-wide
local_dma_lkey, which is not tied to the chunk's MR mapping, so the verbs
layer does not constrain the transfer length to max_chunk_size. msg_id
and off are bounded against queue_depth and max_chunk_size in
rtrs_srv_rdma_done(), but desc[0].len is a separate field that was not
checked against the chunk size.
A peer that advertises desc[0].len larger than max_chunk_size can make
the posted RDMA write read past the chunk's mapped region. The resulting
behaviour depends on the IOMMU configuration: with no IOMMU or in
passthrough mode the read may extend into memory adjacent to the chunk
and be returned to the peer, which can disclose host memory; with a
translating IOMMU the out-of-range access is expected to fault and abort
the connection. In either case the transfer exceeds what the protocol
permits and is driven by a remote peer.
Reject a descriptor length above max_chunk_size, mirroring the existing
off >= max_chunk_size bound in rtrs_srv_rdma_done(). Legitimate clients
do not exceed it: the client sets desc[0].len to its MR length, which is
capped at the negotiated max_io_size (max_chunk_size - MAX_HDR_SIZE). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_ncm: Use unsigned int for ndp_index
The variable ndp_index is declared as a signed integer, but it stores
the return value of get_ncm(), which is unsigned.
A malicious host can supply a large offset that overflows the signed
ndp_index, making it negative. Because ndp_index is compared against
unsigned bounds, this negative value bypasses sanity checks and leads
to an out-of-bounds read when calculating the address of the NDP
block (ntb_ptr + ndp_index).
Fix this by changing ndp_index to unsigned int to ensure consistent
unsigned comparisons throughout the function. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
mpf_ops_parse_header() reads header_size from the bitstream at
MPF_HEADER_SIZE_OFFSET (24). When header_size is zero, the expression
*(buf + header_size - 1) reads one byte before the buffer start.
Since initial_header_size is set to 71 in mpf_ops, the fpga-mgr core
guarantees the buffer is large enough to reach MPF_HEADER_SIZE_OFFSET.
The only real gap is the zero header_size case, which cannot be
resolved by providing a larger buffer, so return -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: bound attr_off in UpdateResidentValue against data_off
In do_action()'s UpdateResidentValue case (fslog.c:3307),
lrh->attr_off and lrh->redo_len come from the on-disk LRH.
When they satisfy aoff + dlen < attr->res.data_off, the
assignment
attr->res.data_size = cpu_to_le32(aoff + dlen - data_off);
underflows to ~4 GiB (e.g. 0xFFFFFFF9 when aoff=0x10, dlen=1,
data_off=0x18). Subsequent code that reads attr->res.data_size
to walk the resident attribute payload would then read up to
4 GiB past the 1024-byte MFT record allocation.
The existing mi_enum_attr() defense in fs/ntfs3/record.c:287
catches the corrupted data_size on the next attribute walk
and fails the mount, but only on the path that walks all
attributes. A read site that picks an attribute by name and
reads its data_size without re-validating is not covered.
Validate aoff against data_off and asize at the source.
Reproduced under UML+KASAN on mainline 8d90b09e6741 via
pr_warn-only probe: with aoff=0x10 and data_off=0x18, the
post-assignment data_size is 0xfffffff9 (mount then fails
at -22 from mi_enum_attr).
[almaz.alexandrovich@paragon-software.com: clang-formatted the changes] |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: validate attribute values on lookup
ntfs_attr_find() and ntfs_external_attr_find() check that generic
resident attribute values fit in their attribute records and that
fixed-size resident values are large enough. For variable-length resident
formats, however, the fixed part is not enough: embedded length fields
can still point callers past the resident value.
A crafted image can set a small resident $FILE_NAME value_length while
leaving file_name_length large. Callers then trust file_name_length and
read past the resident value when converting or comparing the name. This
was reproduced with a crafted image under KASAN as a slab-out-of-bounds
read from the kmalloc-1k MFT record copy. The stack included
ntfs_lookup(), ntfs_iget(), ntfs_read_locked_inode(), ntfs_attr_name_get(),
ntfs_ucstonls(), and utf16s_to_utf8s().
Add a shared attribute value validator and use it before a lookup path
can return an attribute, including the AT_UNUSED enumeration case where
callers inspect returned attributes directly. The helper validates
resident value bounds, minimum resident value sizes, variable-length
$FILE_NAME fields, and non-resident mapping-pairs metadata that was
previously checked separately in both lookup paths.
This also preserves the intended resident @val matching semantics in the
external attribute lookup path. The old duplicated validation block
overwrote the actual resident value length with the type-specific minimum
length before comparing @val, so variable-length resident values could
fail to match even when the bytes were identical. Keep the comparison on
the actual value length, and make ntfs_attrlist_entry_add() compare
resident attributes with lowest_vcn zero instead of reading the
non-resident union member after a successful resident match.
Reject non-resident $FILE_NAME records too: the format requires
$FILE_NAME to be resident and callers treat returned records as resident. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: fix off-by-one in mapping pairs decoding bounds checks
In ntfs_mapping_pairs_decompress(), attr_end points one byte past the
end of the attribute record:
attr_end = (u8 *)attr + le32_to_cpu(attr->length);
The two bounds checks validating that mapping pair data bytes fit within
the attribute use strict greater-than (>), which allows a one-byte
out-of-bounds read when the data extends exactly to attr_end:
b = *buf & 0xf;
if (b) {
if (unlikely(buf + b > attr_end)) // off-by-one
goto io_error;
for (deltaxcn = (s8)buf[b--]; b; b--)
deltaxcn = (deltaxcn << 8) + buf[b];
}
When buf + b == attr_end, the check evaluates to false and buf[b] reads
one byte past the valid attribute boundary. The same pattern appears in
the LCN delta bytes check.
Fix both checks to use >= so that buf[b] at exactly attr_end is
correctly rejected as out of bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: mcast: avoid OOB read of num_dests header
Before the access to struct batadv_tvlv_mcast_tracker's num_dests, it is
attempted to check whether enough space is actually in the network header.
But instead of using offsetofend() to check for the whole size (2) which
must be accessible, offsetof() of is called. The latter is always returning
0. The comparison with the network header length will always return that
enough data is available - even when only 1 or 0 bytes are accessible.
Instead of using offsetofend(), use the more common check for the whole
header. |
