| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: move lsop put work to nvmet_fc_ls_req_op
It’s possible for more than one async command to be in flight from
__nvmet_fc_send_ls_req. For each command, a tgtport reference is taken.
In the current code, only one put work item is queued at a time, which
results in a leaked reference.
To fix this, move the work item to the nvmet_fc_ls_req_op struct, which
already tracks all resources related to the command. |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: add validation for ring_len param
The `ring_len` parameter provided by the virtual function (VF)
is assigned directly to the hardware memory context (HMC) without
any validation.
To address this, introduce an upper boundary check for both Tx and Rx
queue lengths. The maximum number of descriptors supported by the
hardware is 8k-32.
Additionally, enforce alignment constraints: Tx rings must be a multiple
of 8, and Rx rings must be a multiple of 32. |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: fix validation of VF state in get resources
VF state I40E_VF_STATE_ACTIVE is not the only state in which
VF is actually active so it should not be used to determine
if a VF is allowed to obtain resources.
Use I40E_VF_STATE_RESOURCES_LOADED that is set only in
i40e_vc_get_vf_resources_msg() and cleared during reset. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Validate i_depth for exhash directories
A fuzzer test introduced corruption that ends up with a depth of 0 in
dir_e_read(), causing an undefined shift by 32 at:
index = hash >> (32 - dip->i_depth);
As calculated in an open-coded way in dir_make_exhash(), the minimum
depth for an exhash directory is ilog2(sdp->sd_hash_ptrs) and 0 is
invalid as sdp->sd_hash_ptrs is fixed as sdp->bsize / 16 at mount time.
So we can avoid the undefined behaviour by checking for depth values
lower than the minimum in gfs2_dinode_in(). Values greater than the
maximum are already being checked for there.
Also switch the calculation in dir_make_exhash() to use ilog2() to
clarify how the depth is calculated.
Tested with the syzkaller repro.c and xfstests '-g quick'. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Skip fastpath emulation on VM-Exit if next RIP isn't valid
Skip the WRMSR and HLT fastpaths in SVM's VM-Exit handler if the next RIP
isn't valid, e.g. because KVM is running with nrips=false. SVM must
decode and emulate to skip the instruction if the CPU doesn't provide the
next RIP, and getting the instruction bytes to decode requires reading
guest memory. Reading guest memory through the emulator can fault, i.e.
can sleep, which is disallowed since the fastpath handlers run with IRQs
disabled.
BUG: sleeping function called from invalid context at ./include/linux/uaccess.h:106
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 32611, name: qemu
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 30580
hardirqs last enabled at (30579): [<ffffffffc08b2527>] vcpu_run+0x1787/0x1db0 [kvm]
hardirqs last disabled at (30580): [<ffffffffb4f62e32>] __schedule+0x1e2/0xed0
softirqs last enabled at (30570): [<ffffffffb4247a64>] fpu_swap_kvm_fpstate+0x44/0x210
softirqs last disabled at (30568): [<ffffffffb4247a64>] fpu_swap_kvm_fpstate+0x44/0x210
CPU: 298 UID: 0 PID: 32611 Comm: qemu Tainted: G U 6.16.0-smp--e6c618b51cfe-sleep #782 NONE
Tainted: [U]=USER
Hardware name: Google Astoria-Turin/astoria, BIOS 0.20241223.2-0 01/17/2025
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xb0
__might_resched+0x271/0x290
__might_fault+0x28/0x80
kvm_vcpu_read_guest_page+0x8d/0xc0 [kvm]
kvm_fetch_guest_virt+0x92/0xc0 [kvm]
__do_insn_fetch_bytes+0xf3/0x1e0 [kvm]
x86_decode_insn+0xd1/0x1010 [kvm]
x86_emulate_instruction+0x105/0x810 [kvm]
__svm_skip_emulated_instruction+0xc4/0x140 [kvm_amd]
handle_fastpath_invd+0xc4/0x1a0 [kvm]
vcpu_run+0x11a1/0x1db0 [kvm]
kvm_arch_vcpu_ioctl_run+0x5cc/0x730 [kvm]
kvm_vcpu_ioctl+0x578/0x6a0 [kvm]
__se_sys_ioctl+0x6d/0xb0
do_syscall_64+0x8a/0x2c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f479d57a94b
</TASK>
Note, this is essentially a reapply of commit 5c30e8101e8d ("KVM: SVM:
Skip WRMSR fastpath on VM-Exit if next RIP isn't valid"), but with
different justification (KVM now grabs SRCU when skipping the instruction
for other reasons). |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: fix null pointer dereference on zero-length checksum
In xdr_stream_decode_opaque_auth(), zero-length checksum.len causes
checksum.data to be set to NULL. This triggers a NPD when accessing
checksum.data in gss_krb5_verify_mic_v2(). This patch ensures that
the value of checksum.len is not less than XDR_UNIT. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dlink: handle copy_thresh allocation failure
The driver did not handle failure of `netdev_alloc_skb_ip_align()`.
If the allocation failed, dereferencing `skb->protocol` could lead to
a NULL pointer dereference.
This patch tries to allocate `skb`. If the allocation fails, it falls
back to the normal path.
Tested-on: D-Link DGE-550T Rev-A3 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_objref: validate objref and objrefmap expressions
Referencing a synproxy stateful object from OUTPUT hook causes kernel
crash due to infinite recursive calls:
BUG: TASK stack guard page was hit at 000000008bda5b8c (stack is 000000003ab1c4a5..00000000494d8b12)
[...]
Call Trace:
__find_rr_leaf+0x99/0x230
fib6_table_lookup+0x13b/0x2d0
ip6_pol_route+0xa4/0x400
fib6_rule_lookup+0x156/0x240
ip6_route_output_flags+0xc6/0x150
__nf_ip6_route+0x23/0x50
synproxy_send_tcp_ipv6+0x106/0x200
synproxy_send_client_synack_ipv6+0x1aa/0x1f0
nft_synproxy_do_eval+0x263/0x310
nft_do_chain+0x5a8/0x5f0 [nf_tables
nft_do_chain_inet+0x98/0x110
nf_hook_slow+0x43/0xc0
__ip6_local_out+0xf0/0x170
ip6_local_out+0x17/0x70
synproxy_send_tcp_ipv6+0x1a2/0x200
synproxy_send_client_synack_ipv6+0x1aa/0x1f0
[...]
Implement objref and objrefmap expression validate functions.
Currently, only NFT_OBJECT_SYNPROXY object type requires validation.
This will also handle a jump to a chain using a synproxy object from the
OUTPUT hook.
Now when trying to reference a synproxy object in the OUTPUT hook, nft
will produce the following error:
synproxy_crash.nft: Error: Could not process rule: Operation not supported
synproxy name mysynproxy
^^^^^^^^^^^^^^^^^^^^^^^^ |
| In the Linux kernel, the following vulnerability has been resolved:
kernel/sys.c: fix the racy usage of task_lock(tsk->group_leader) in sys_prlimit64() paths
The usage of task_lock(tsk->group_leader) in sys_prlimit64()->do_prlimit()
path is very broken.
sys_prlimit64() does get_task_struct(tsk) but this only protects task_struct
itself. If tsk != current and tsk is not a leader, this process can exit/exec
and task_lock(tsk->group_leader) may use the already freed task_struct.
Another problem is that sys_prlimit64() can race with mt-exec which changes
->group_leader. In this case do_prlimit() may take the wrong lock, or (worse)
->group_leader may change between task_lock() and task_unlock().
Change sys_prlimit64() to take tasklist_lock when necessary. This is not
nice, but I don't see a better fix for -stable. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid potential buffer over-read in parse_apply_sb_mount_options()
Unlike other strings in the ext4 superblock, we rely on tune2fs to
make sure s_mount_opts is NUL terminated. Harden
parse_apply_sb_mount_options() by treating s_mount_opts as a potential
__nonstring. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix metadata_dst leak __bpf_redirect_neigh_v{4,6}
Cilium has a BPF egress gateway feature which forces outgoing K8s Pod
traffic to pass through dedicated egress gateways which then SNAT the
traffic in order to interact with stable IPs outside the cluster.
The traffic is directed to the gateway via vxlan tunnel in collect md
mode. A recent BPF change utilized the bpf_redirect_neigh() helper to
forward packets after the arrival and decap on vxlan, which turned out
over time that the kmalloc-256 slab usage in kernel was ever-increasing.
The issue was that vxlan allocates the metadata_dst object and attaches
it through a fake dst entry to the skb. The latter was never released
though given bpf_redirect_neigh() was merely setting the new dst entry
via skb_dst_set() without dropping an existing one first. |
| In the Linux kernel, the following vulnerability has been resolved:
uio_hv_generic: Let userspace take care of interrupt mask
Remove the logic to set interrupt mask by default in uio_hv_generic
driver as the interrupt mask value is supposed to be controlled
completely by the user space. If the mask bit gets changed
by the driver, concurrently with user mode operating on the ring,
the mask bit may be set when it is supposed to be clear, and the
user-mode driver will miss an interrupt which will cause a hang.
For eg- when the driver sets inbound ring buffer interrupt mask to 1,
the host does not interrupt the guest on the UIO VMBus channel.
However, setting the mask does not prevent the host from putting a
message in the inbound ring buffer. So let’s assume that happens,
the host puts a message into the ring buffer but does not interrupt.
Subsequently, the user space code in the guest sets the inbound ring
buffer interrupt mask to 0, saying “Hey, I’m ready for interrupts”.
User space code then calls pread() to wait for an interrupt.
Then one of two things happens:
* The host never sends another message. So the pread() waits forever.
* The host does send another message. But because there’s already a
message in the ring buffer, it doesn’t generate an interrupt.
This is the correct behavior, because the host should only send an
interrupt when the inbound ring buffer transitions from empty to
not-empty. Adding an additional message to a ring buffer that is not
empty is not supposed to generate an interrupt on the guest.
Since the guest is waiting in pread() and not removing messages from
the ring buffer, the pread() waits forever.
This could be easily reproduced in hv_fcopy_uio_daemon if we delay
setting interrupt mask to 0.
Similarly if hv_uio_channel_cb() sets the interrupt_mask to 1,
there’s a race condition. Once user space empties the inbound ring
buffer, but before user space sets interrupt_mask to 0, the host could
put another message in the ring buffer but it wouldn’t interrupt.
Then the next pread() would hang.
Fix these by removing all instances where interrupt_mask is changed,
while keeping the one in set_event() unchanged to enable userspace
control the interrupt mask by writing 0/1 to /dev/uioX. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Don't (re)check L1 intercepts when completing userspace I/O
When completing emulation of instruction that generated a userspace exit
for I/O, don't recheck L1 intercepts as KVM has already finished that
phase of instruction execution, i.e. has already committed to allowing L2
to perform I/O. If L1 (or host userspace) modifies the I/O permission
bitmaps during the exit to userspace, KVM will treat the access as being
intercepted despite already having emulated the I/O access.
Pivot on EMULTYPE_NO_DECODE to detect that KVM is completing emulation.
Of the three users of EMULTYPE_NO_DECODE, only complete_emulated_io() (the
intended "recipient") can reach the code in question. gp_interception()'s
use is mutually exclusive with is_guest_mode(), and
complete_emulated_insn_gp() unconditionally pairs EMULTYPE_NO_DECODE with
EMULTYPE_SKIP.
The bad behavior was detected by a syzkaller program that toggles port I/O
interception during the userspace I/O exit, ultimately resulting in a WARN
on vcpu->arch.pio.count being non-zero due to KVM no completing emulation
of the I/O instruction.
WARNING: CPU: 23 PID: 1083 at arch/x86/kvm/x86.c:8039 emulator_pio_in_out+0x154/0x170 [kvm]
Modules linked in: kvm_intel kvm irqbypass
CPU: 23 UID: 1000 PID: 1083 Comm: repro Not tainted 6.16.0-rc5-c1610d2d66b1-next-vm #74 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:emulator_pio_in_out+0x154/0x170 [kvm]
PKRU: 55555554
Call Trace:
<TASK>
kvm_fast_pio+0xd6/0x1d0 [kvm]
vmx_handle_exit+0x149/0x610 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xda8/0x1ac0 [kvm]
kvm_vcpu_ioctl+0x244/0x8c0 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0x5d/0xc60
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: Defer ip_vs_ftp unregister during netns cleanup
On the netns cleanup path, __ip_vs_ftp_exit() may unregister ip_vs_ftp
before connections with valid cp->app pointers are flushed, leading to a
use-after-free.
Fix this by introducing a global `exiting_module` flag, set to true in
ip_vs_ftp_exit() before unregistering the pernet subsystem. In
__ip_vs_ftp_exit(), skip ip_vs_ftp unregister if called during netns
cleanup (when exiting_module is false) and defer it to
__ip_vs_cleanup_batch(), which unregisters all apps after all connections
are flushed. If called during module exit, unregister ip_vs_ftp
immediately. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix incorrect io_kiocb reference in io_link_skb
In io_link_skb function, there is a bug where prev_notif is incorrectly
assigned using 'nd' instead of 'prev_nd'. This causes the context
validation check to compare the current notification with itself instead
of comparing it with the previous notification.
Fix by using the correct prev_nd parameter when obtaining prev_notif. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd/pgtbl: Fix possible race while increase page table level
The AMD IOMMU host page table implementation supports dynamic page table levels
(up to 6 levels), starting with a 3-level configuration that expands based on
IOVA address. The kernel maintains a root pointer and current page table level
to enable proper page table walks in alloc_pte()/fetch_pte() operations.
The IOMMU IOVA allocator initially starts with 32-bit address and onces its
exhuasted it switches to 64-bit address (max address is determined based
on IOMMU and device DMA capability). To support larger IOVA, AMD IOMMU
driver increases page table level.
But in unmap path (iommu_v1_unmap_pages()), fetch_pte() reads
pgtable->[root/mode] without lock. So its possible that in exteme corner case,
when increase_address_space() is updating pgtable->[root/mode], fetch_pte()
reads wrong page table level (pgtable->mode). It does compare the value with
level encoded in page table and returns NULL. This will result is
iommu_unmap ops to fail and upper layer may retry/log WARN_ON.
CPU 0 CPU 1
------ ------
map pages unmap pages
alloc_pte() -> increase_address_space() iommu_v1_unmap_pages() -> fetch_pte()
pgtable->root = pte (new root value)
READ pgtable->[mode/root]
Reads new root, old mode
Updates mode (pgtable->mode += 1)
Since Page table level updates are infrequent and already synchronized with a
spinlock, implement seqcount to enable lock-free read operations on the read path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: increase scan_ies_len for S1G
Currently the S1G capability element is not taken into account
for the scan_ies_len, which leads to a buffer length validation
failure in ieee80211_prep_hw_scan() and subsequent WARN in
__ieee80211_start_scan(). This prevents hw scanning from functioning.
To fix ensure we accommodate for the S1G capability length. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/slub: avoid accessing metadata when pointer is invalid in object_err()
object_err() reports details of an object for further debugging, such as
the freelist pointer, redzone, etc. However, if the pointer is invalid,
attempting to access object metadata can lead to a crash since it does
not point to a valid object.
One known path to the crash is when alloc_consistency_checks()
determines the pointer to the allocated object is invalid because of a
freelist corruption, and calls object_err() to report it. The debug code
should report and handle the corruption gracefully and not crash in the
process.
In case the pointer is NULL or check_valid_pointer() returns false for
the pointer, only print the pointer value and skip accessing metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: fix invalid accesses to ceph_connection_v1_info
There is a place where generic code in messenger.c is reading and
another place where it is writing to con->v1 union member without
checking that the union member is active (i.e. msgr1 is in use).
On 64-bit systems, con->v1.auth_retry overlaps with con->v2.out_iter,
so such a read is almost guaranteed to return a bogus value instead of
0 when msgr2 is in use. This ends up being fairly benign because the
side effect is just the invalidation of the authorizer and successive
fetching of new tickets.
con->v1.connect_seq overlaps with con->v2.conn_bufs and the fact that
it's being written to can cause more serious consequences, but luckily
it's not something that happens often. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix one NULL pointer dereference in smc_ib_is_sg_need_sync()
BUG: kernel NULL pointer dereference, address: 00000000000002ec
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP PTI
CPU: 28 UID: 0 PID: 343 Comm: kworker/28:1 Kdump: loaded Tainted: G OE 6.17.0-rc2+ #9 NONE
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_ib_is_sg_need_sync+0x9e/0xd0 [smc]
...
Call Trace:
<TASK>
smcr_buf_map_link+0x211/0x2a0 [smc]
__smc_buf_create+0x522/0x970 [smc]
smc_buf_create+0x3a/0x110 [smc]
smc_find_rdma_v2_device_serv+0x18f/0x240 [smc]
? smc_vlan_by_tcpsk+0x7e/0xe0 [smc]
smc_listen_find_device+0x1dd/0x2b0 [smc]
smc_listen_work+0x30f/0x580 [smc]
process_one_work+0x18c/0x340
worker_thread+0x242/0x360
kthread+0xe7/0x220
ret_from_fork+0x13a/0x160
ret_from_fork_asm+0x1a/0x30
</TASK>
If the software RoCE device is used, ibdev->dma_device is a null pointer.
As a result, the problem occurs. Null pointer detection is added to
prevent problems. |