| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
x86/boot: Validate console=uart8250 baud rate to fix early boot hang
When the baud rate is empty, 0, invalid, or overflows to 0 when stored
as an int, the system will hang during early boot because of a division
by zero in early_serial_init().
Fall back to DEFAULT_BAUD when the resulting baud rate is 0 to prevent
an early system hang. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: fix permanently busy scans after multiple roam iterations
In order for the firmware to sleep, the driver has to confirm a
previously received sleep request. The normal sequence of evets goes
like this:
EVENT_SLEEP -> adapter->ps_state = PS_STATE_PRE_SLEEP -> sleep-confirm
-> SLEEP -> EVENT_AWAKE -> AWAKE.
Before sending the sleep-confirm command, the driver must make sure
there are no commands either running or waiting to be completed.
mwifiex_ret_802_11_associate() unconditionally sets
ps_state = PS_STATE_AWAKE when it processes the association command
response, outside of the normal powersave management flow. If
EVENT_SLEEP arrives while the association command is in flight,
ps_state is PRE_SLEEP when the association command response is parsed,
and the forced AWAKE overwrites it. The deferred sleep-confirm is
never sent.
A subsequent scan_start command is correctly acknowledged, but the
firmware doesn't generate scan_result events. The scan request never
finishes, and additional requests from userspace fail with -EBUSY.
After testing on both IW412 and W8997, I could only trigger the bug on
the IW412 and observed the firmwares behave differently. On the IW412
the firmware still sends EVENT_SLEEP while the authentication /
association process is ongoing. A W8997 under the same
conditions seems to suppress power-save for the duration of the
association, so PRE_SLEEP never coincided with the association response
even after extended periods of testing using the loops
described below (>12hours).
On the IW412, the delay between commands that triggers an EVENT_SLEEP
was empirically determined to be ~20ms. This delay can naturally occur
when the driver is outputting debugging information
(debug_mask = 0x00000037), in which situation the busy scans issue is
repeatable while running "test 1)" as described below. If the delay
between commands is less than ~20ms, the firmware stays awake and
the issue was not reproducible running the same test.
The host_mlme=false path also behaves differently. In this case, the
entire authentication / association transaction is executed by one
command (HostCmd_CMD_802_11_ASSOCIATE), and the firmware doesn't emit
EVENT_SLEEP while the command is running.
Remove the assignment so the ps_state is only manipulated in the paths
that are related to powersave event handling and on the main workqueue
for correct sleep confirmation.
The following loop tests were performed (with debugging output enabled):
1) force roaming between two AP's, one 5GHz and one 2.4GHz, same
SSID. Use wpa_cli to trigger the roaming behavior, sleep 2s
between iterations.
2) force a disconnection to AP 1 and a connection to AP 2, test
scan. Use wpa_cli to trigger the connection changes, sleep 2s
between iterations.
Each test ran in each device for at least 3 hours. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled interrupt
When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning
occurs. This happens because the usdhc interrupt is not disabled during
system suspend when device_may_wakeup() returns false.
The sequence of events leading to this issue:
1. System enters suspend without disabling usdhc interrupt
(because device_may_wakeup() returns false for usdhc device)
2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt
3. WIFI sends a Card interrupt before usdhc has fully resumed
4. usdhc is still in runtime suspend state and cannot handle the
interrupt properly
5. The unhandled interrupt triggers "nobody cared" warning
Fix this by unconditionally disabling the usdhc interrupt during suspend
and re-enabling it during resume, regardless of the wakeup capability.
This ensures no interrupts are processed during the suspend/resume
transition. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect()
ueagle-atm uses the asynchronous request_firmware_nowait() in .probe(),
but does not wait for its completion, not even in .disconnect(); so, if the
device is unplugged meanwhile, its teardown runs concurrently with that.
Even though this inconsistency is worth addressing on its own, it has also
triggered several bug reports in syzbot over the years (some auto-closed)
where the firmware sysfs fallback mechanism (CONFIG_FW_LOADER_USER_HELPER)
creates a firmware subdirectory in the device directory during its removal,
which might hit unexpected conditions in kernfs, apparently, depending at
which point the add and remove operations raced. (See links.)
The pattern is:
usb ?-?: Direct firmware load for ueagle-atm/eagle?.fw failed with error -2
usb ?-?: Falling back to sysfs fallback for: ueagle-atm/eagle?.fw
<ERROR>
Call trace:
...
kernfs_create_dir_ns
sysfs_create_dir_ns
create_dir
kobject_add_internal
kobject_add_varg
kobject_add
class_dir_create_and_add
get_device_parent
device_add
fw_load_sysfs_fallback
fw_load_from_user_helper
firmware_fallback_sysfs
_request_firmware
request_firmware_work_func
...
(Some variations are observed, after fw_load_sysfs_fallback(), e.g., [1].)
While the kernfs side is being looked at, the ueagle-atm side can be fixed
by waiting for the pre-firmware load in the .disconnect() handler.
This change has a similar approach to previous work by Andrey Tsygunka [2]
(wait_for_completion() in .disconnect()), but it is relatively different in
design/implementation; using the Originally-by tag for credit assignment.
This has been tested with:
- synthetic reproducer to check the error path;
- USB gadget (virtual device) to check the firmware upload path;
- QEMU device emulator to check the device ID re-enumeration path;
(The latter two were written by Claude; no other code/text in this commit.)
Links (year first reported):
2025 https://syzbot.org/bug?extid=ce1e5a1b4e086b43e56d
2025 https://syzbot.org/bug?extid=9af8471255ac36e34fd4
2024 https://syzbot.org/bug?extid=306212936b13e520679d
2023 https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
2022 https://syzbot.org/bug?extid=782984d6f1701b526edb
2021 https://syzbot.org/bug?id=f3f221579f4ef7e9691281f3c6f56c05f83e8490
2021 https://syzbot.org/bug?id=84d86f0d71394829df6fc53daf6642c045983881
2021 https://syzbot.org/bug?id=3302dc1c0e2b9c94f2e8edb404eabc9267bc6f90
[1] https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
[2] https://lore.kernel.org/lkml/20250410093146.3776801-2-aitsygunka@yandex.ru/ |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: clear sock_ops cb flags before force-closing a child socket
A child socket inherits the listener's bpf_sock_ops_cb_flags via
sk_clone_lock(). If its setup fails in tcp_v4_syn_recv_sock() /
tcp_v6_syn_recv_sock(), the child is freed through put_and_exit, where
inet_csk_prepare_forced_close() drops the socket lock and tcp_done() runs
without it.
If BPF_SOCK_OPS_STATE_CB_FLAG was inherited, tcp_done() -> tcp_set_state()
calls tcp_call_bpf(), which expects the lock and trips sock_owned_by_me():
WARNING: include/net/sock.h:1799 at tcp_set_state+0x433/0x550
RIP: 0010:tcp_set_state+0x433/0x550 include/net/sock.h:1799
Call Trace:
<IRQ>
tcp_done+0xba/0x250 net/ipv4/tcp.c:5095
tcp_v4_syn_recv_sock+0x850/0xa50 net/ipv4/tcp_ipv4.c:1787
tcp_check_req+0xf30/0x1360 net/ipv4/tcp_minisocks.c:926
tcp_v4_rcv+0x1047/0x1b50 net/ipv4/tcp_ipv4.c:2164
</IRQ>
The child is freed before it is ever established, so it should run no
sock_ops callback. Clear its cb flags in inet_csk_prepare_for_destroy_sock(),
the common point for the IPv4, IPv6 and chtls forced-close paths and for the
MPTCP ->syn_recv_sock() failure path (dispose_child), which reaches tcp_done()
on a child that was never established too. |
| In the Linux kernel, the following vulnerability has been resolved:
vduse: Fix race in vduse_dev_msg_sync and vduse_dev_read_iter
There is one race case in vduse_dev_msg_sync and vduse_dev_read_iter:
vduse_dev_read_iter():
lock(msg_lock);
dequeue_msg(send_list);
unlock(msg_lock);
vduse_dev_msg_sync():
wait_timeout() finish
lock(msg_lock);
check msg->complete is false
list_del(msg); <- double list_del() crash!
To fix this case, we shall ensure vduse_msg is on send_list or recv_list
outside the msg_lock critical section. |
| rsync before 3.5.0 contains a symlink race condition vulnerability that allows local attackers to cause rsync to apply arbitrary ACLs or extended attributes to unintended files by substituting a symlink at a predictable destination path between the file write and the subsequent acl_set_file() or lsetxattr() call. Attackers can exploit this timing window to redirect ACL and xattr application through a crafted symlink to files outside the intended destination tree, potentially granting elevated permissions and enabling local privilege escalation. |
| OP-TEE OS through 4.10.0, fixed in commit 8794043, contains a use-after-free vulnerability in the Trusted Application loader that allows attackers with the ability to load a signed Trusted Application to corrupt secure-world kernel memory by setting the TA_FLAG_CONCURRENT flag in a user TA signed header. Attackers can cause two concurrent sessions to operate on the same shared context without locking, corrupting the uctx->vm_info.regions list during memref parameter mapping and unmapping to free vm_region nodes still in use, resulting in a use-after-free in S-EL1 secure-world kernel memory. |
| llama.cpp builds b1886 through b7445 contain a race condition use-after-free vulnerability in the LLaMA-Android JNI wrapper where bench_1model() and free_1context() lack synchronization, allowing Thread A to operate on freed memory while Thread B concurrently frees the llama_context. Attackers can exploit this by performing heap spray with attacker-controlled data containing a fake vtable to hijack the vtable pointer at offset +0x30, causing llama_batch_allocr::clear() to dereference arbitrary memory and achieve remote code execution. |
| LightFTP 2.3.1 contains a residual race condition vulnerability (an incomplete fix for CVE-2024-11144) in the worker_thread_cleanup() function of ftpserv.c that allows remote unauthenticated attackers to destabilize or crash the daemon by triggering unsynchronized access to shared per-connection state without holding the required mutex lock. Attackers can send a data-transfer command such as LIST followed immediately by ABOR to exploit the missing synchronization on shared context and detached thread id reuse, resulting in daemon destabilization or crash which can lead to a denial of service. The 2.3.1 patch only narrowed the timing window (an extra re-check and reordered cleanup), it never added the missing lock, so the underlying race remains. |
| rsync before 3.5.0 contains a symlink race condition vulnerability in the sender's directory scanning logic that allows attackers to cause the sender to enumerate and transfer files outside the module root's intended subtree. Attackers who can create or manipulate symlinks in a path component of the scanned tree can replace a symlink with a directory entry pointing outside the module root between the lstat() call and the subsequent opendir() call, exposing files beyond the intended root in both daemon-mode and non-daemon sender-side scanning. |
| rsync before 3.5.0 contains a symlink race condition vulnerability in the --remove-source-files feature that allows attackers with symlink creation access to cause arbitrary file deletion. Attackers can atomically substitute a symlink for a source file between transfer completion and the unlink() call, causing rsync to delete the symlink target rather than the intended source file. |
| rsync before 3.5.0 contains a symlink race condition vulnerability in the sender's source tree traversal that allows an attacker who can manipulate a parent directory of the source tree to redirect file reads to unintended paths. Attackers can atomically replace a parent directory component with a symlink pointing outside the source root between path resolution and file open operations to disclose file contents outside the intended transfer root. |
| rsync before 3.5.0 contains a time-of-check to time-of-use (TOCTOU) race condition vulnerability in the non-daemon receiver's destination directory handling that allows an attacker who can manipulate destination path parent components to redirect file writes to unintended locations. Attackers can substitute a symlink for a component of the destination path between the path resolution and chdir() call, causing the receiver's working directory to be established outside the intended destination tree so that subsequent relative-path file writes land in unintended filesystem locations. |
| llama.cpp builds b7492 through the latest b9060 contains a use-after-free vulnerability in llama-server affecting six tokenization endpoints (/tokenize, /detokenize, /infill, /apply-template, /rerank, and /anthropic/count_tokens) that bypass the task queue and access ctx_server.vocab directly on HTTP worker threads. Attackers can exploit a time-of-check-time-of-use race condition where the main thread destroys and frees vocab after the synchronization lock is released but before the handler finishes using it, causing a crash or potential code execution when --sleep-idle-seconds is configured. |
| llama.cpp builds b7492 through the latest b9060 contains a use-after-free vulnerability in the vocab pointer of llama-server when the --sleep-idle-seconds feature is enabled, allowing unauthenticated remote attackers to execute arbitrary code. Attackers can trigger the vulnerability by sending requests to affected endpoints while the server transitions to sleep mode, causing concurrent worker threads to dereference a freed vocab pointer that can be reclaimed with attacker-controlled data to achieve remote code execution. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to gain unauthorized access to system objects due to a time-of-check to time-of-use (TOCTOU) race condition involving symbolic links. |
| Concurrent execution using shared resource with improper synchronization ('race condition') in Remote Desktop Client allows an unauthorized attacker to execute code over a network. |
| Concurrent execution using shared resource with improper synchronization ('race condition') in Windows Telephony Service allows an authorized attacker to elevate privileges locally. |
| Concurrent execution using shared resource with improper synchronization ('race condition') in Windows Event Logging Service allows an authorized attacker to elevate privileges locally. |
