| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: fix xfrm_state_construct() auth-trunc leak
attach_auth_trunc() can allocate x->aalg while leaving
x->props.aalgo at zero when the selected auth algorithm has no
sadb_alg_id. One real case is cmac(aes).
xfrm_state_construct() then treats !x->props.aalgo as "no auth
algorithm attached yet" and calls attach_auth(). That overwrites
x->aalg and loses the first allocation. Any later failure or teardown
only frees the replacement pointer.
Check whether x->aalg is already attached instead of inferring that
state from x->props.aalgo. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: clamp route advmss to TCP_MIN_MSS
tcp_select_initial_window() assumes that callers never pass an MSS
smaller than 1, but route-derived advmss values can violate that
assumption.
A too-small explicit RTAX_ADVMSS is one way to get there, but it is not
the only one. The same divide-by-zero can also be reached through the
"default advmss" path when RTAX_ADVMSS is left at 0 and the effective
advmss is later driven down by route MTU and min_adv_mss.
Introduce a tcp_dst_advmss() helper that clamps route advmss to
TCP_MIN_MSS before TCP consumes it, and use it in the TCP paths that
derive advmss from dst metrics. This keeps the effective MSS from
dropping to zero before tcp_select_initial_window() rounds the receive
window. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_tcm: keep port count until LUN teardown completes
tcm_usbg_drop_nexus() permits session removal once tpg_port_count
reaches zero. However, usbg_port_unlink() currently decrements that
count from the fabric_pre_unlink() callback, before core_dev_del_lun()
waits for active se_lun references to drain.
If removal of the last LUN races a nexus removal, the latter can observe
a zero port count and call target_remove_session(). This frees
sess_cmd_map while an in-flight struct usbg_cmd, including its work item,
can still be accessed.
Overlapping the last-LUN unlink with nexus removal reproduces this
lifetime violation as a DEBUG_OBJECTS "free active" warning for
usbg_cmd_work, followed by a target-core BUG/Oops.
The generic target-core unlink path has no callback after
core_dev_del_lun() completes. Add an optional fabric_post_unlink()
callback and use it for the f_tcm port count. The count now remains
nonzero until core_dev_del_lun() has finished draining active LUN
references, preventing nexus removal from freeing the session during
command completion. |
| IBM Db2 Mirror for i 7.4, 7.5, and 7.6 could allow a local attacker to obtain information due to a race condition involving a predictable Unix domain socket path in a world-writable directory. |
| In the Linux kernel, the following vulnerability has been resolved:
futex/pi: Reject cross-mm private futex owners
A private futex key borrows the waiter's mm without taking an mm_users
reference. Nevertheless, attach_to_pi_owner() currently accepts an owner
from a different address space and copies the private key into the owner's
PI state.
When that owner exits, exit_pi_state_list() uses the saved key to find the
hash bucket and acquires a reference to the waiter's private hash. If the
last user of the waiter's mm exits concurrently, futex_hash_free() frees
the hash while the owner still uses its bucket and reference.
Prevent this by validating in attach_to_pi_owner() that, for private
futexes, the owner mm and waiter mm are the same. Perform the check with
the owner's pi_lock held and after validating owner::futex::state to
serialize against a concurrent PI-state exit cleanup.
[ tglx: Amended comment ] |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: pm: fix memory leak from alloc-during-teardown race
mptcp_pm_destroy() empties msk->pm.anno_list and
msk->pm.userspace_pm_local_addr_list under msk->pm.lock during socket
teardown, dropping the lock between the two.
A concurrent userspace PM genl ANNOUNCE on the same msk holds a sock
reference via mptcp_token_get_sock() and, in
mptcp_pm_nl_announce_doit(), calls
mptcp_userspace_pm_append_new_local_addr() and
mptcp_pm_announced_alloc(). Both take msk->pm.lock briefly to add to
their respective lists. Because the genl handler holds a sock reference,
mptcp_pm_destroy() may run on the same msk via mptcp_disconnect(), which
invokes mptcp_destroy_common() without dropping the sock refcount,
before the handler completes.
If the lock acquisitions interleave such that mptcp_pm_destroy() empties
a list first, the later alloc adds its entry to a list head that nothing
else iterates for this msk, and the entry leaks. kmemleak reports both
mptcp_pm_add_addr objects (from mptcp_pm_announced_alloc()) and
mptcp_pm_addr_entry objects (from
mptcp_userspace_pm_append_new_local_addr()) under sustained concurrent
ANNOUNCE + close load against the userspace PM.
Add an MPTCP_PM_DESTROYING bit in msk->pm.status, set by
mptcp_pm_destroy() under pm.lock before the lists are emptied and
checked under pm.lock by the alloc paths. Either the alloc takes pm.lock
first, in which case its entry is on the list when mptcp_pm_destroy()
frees it; or mptcp_pm_destroy() takes pm.lock first, in which case the
later alloc observes the bit and refuses.
Found by an MPTCP protocol-flow harness extending BRF (arXiv:2305.08782). |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Fix race on the initial mm->futex.phash.ref allocation
futex_hash_allocate() allocates mm->futex.phash.ref without any locking.
Commit d9b05321e21e ("futex: Move futex_hash_free() back to __mmput()")
moved the allocation here and assumed that the process has just a single
thread at this point.
Commit ee9dce44362b ("futex: Drop CLONE_THREAD requirement for private
default hash alloc") widened need_futex_hash_allocate_default() to cover
any CLONE_VM clone, but left out vfork because the parent is suspended and
cannot race.
That no longer holds once vfork is nested. If a vfork child calls vfork
again and is then killed with SIGKILL, the parent is released from its
vfork wait and runs concurrently with the grandchild in the same mm.
Neither of them went through futex_hash_allocate_default().
When both call prctl(PR_FUTEX_HASH, PR_FUTEX_HASH_SET_SLOTS) at the same
time, each one sees mm->futex.phash.ref as NULL and stores its own percpu
counter. Only the last store survives. The counter stored first is no
longer reachable from the mm, so the references on it are not seen by
__futex_ref_atomic_end(). A private hash that still has references is then
considered dead and freed, and a task that still holds one of its buckets
writes into freed memory in futex_q_lock().
Store the counter once with cmpxchg() and let the loser free_percpu() its
own. The initial reference has to be taken before the store, otherwise
another task can install a private hash while the counter is still 0. |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Fix race in futex_pivot_pending() during private hash resize
A task performing a custom private hash resize can remain blocked in
uninterruptible sleep indefinitely. The hung-task detector reports:
INFO: task futex-resizer:314 blocked for more than 10 seconds.
task:futex-resizer state:D stack:14824 pid:314 tgid:312 ppid:311
Call Trace:
__schedule+0x521/0xf30
schedule+0x22/0xa0
futex_hash_allocate+0x3db/0x490
__do_sys_prctl+0x6f5/0xbd0
do_syscall_64+0xf9/0x530
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Kernel panic - not syncing: hung_task: blocked tasks
futex_pivot_pending() allows the resize request to continue when
either no replacement hash is pending (hash_new == NULL) or the current
hash reference count has reached zero.
After the final-reference wake, another futex task can complete the
pivot between the two observations:
T1 T2
futex_hash_allocate()
wait_var_event(mm, ...)
futex_pivot_pending(mm)
hash_new != NULL
futex_hash()
futex_ref_get(old) -> false
futex_pivot_hash(mm)
hash_new = NULL
__futex_pivot_hash(mm, new)
rcu_assign_pointer(hash, new)
fph = rcu_dereference(hash) /* new */
futex_ref_is_dead(fph) -> false
schedule()
The pivot changes the state from hash_new != NULL with a dead current
hash to hash_new == NULL with a live current hash. Because
futex_pivot_pending() reads hash_new and hash without serialization,
the resize task can observe hash_new in the pre-pivot state and hash in
the post-pivot state, causing futex_pivot_pending() to return false even
though the pivot has completed. The task then goes to sleep after the
wakeup has already been consumed.
Serialize state reads in futex_pivot_pending() using futex_mm_phash::lock.
This guarantees that futex_pivot_pending() observes hash_new and hash
atomically, eliminating the race condition. |
| In the Linux kernel, the following vulnerability has been resolved:
futex/pi: Plug private futex exec() race
The check for private futexes whether the waiter's mm, which is stored in
the futex_key and copied into the pi_state, is the same as the owner's mm
is not sufficient for exec(). exec() has a gap where the mm check fails to
give the correct answer:
exec()
...
exec_release_mm()
futex_exec_release()
tsk::futex::exit_state = EXITING;
cleanup_robust_list();
1) tsk::futex::exit_state = OK;
...
old_mm = tsk::mm;
2) tsk::mm = ->mm;
Between #1 and #2 the check for the mm is wrong as that mm is about to be
swapped out and eventually freed.
Plug this gap by:
1) Setting tsk::futex::exit_state to FUTEX_STATE_DEAD in
futex_exec_release()
2) Setting tsk::futex::exit_state to FUTEX_STATE_OK after
the mm has been switched.
From a futex point of view the task is dead after it finished the robust
list cleanup up to the point where it sets the state to OK again. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: serialize mode sysfs access with lock_fb_info()
show_mode(), show_modes(), and store_mode() access fb_info->modelist
and fb_info->mode without holding lock_fb_info(). store_modes() takes
lock_fb_info() while replacing the modelist and freeing the old one.
A concurrent reader or writer can load a pointer to an old modelist
entry before store_modes() frees it, then dereference freed memory or
store a stale freed pointer in fb_info->mode.
Take lock_fb_info() in show_mode(), show_modes(), and store_mode() to
serialize with store_modes(). In show_mode(), copy the mode to the
stack and format after dropping the lock. In store_mode(), split
activate() into a _locked variant to avoid double-locking, and hold
the locks for the modelist walk, mode conversion, activation, and
fb_info->mode assignment together. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: appleir: fix UAF on pending key_up_timer in remove()
appleir_remove() runs hid_hw_stop() before timer_delete_sync().
hid_hw_stop() synchronously unregisters the HID input device via
hid_disconnect() -> hidinput_disconnect() -> input_unregister_device(),
which drops the last reference and frees the underlying input_dev when
no userspace handle holds it open.
key_up_tick() reads appleir->input_dev and calls input_report_key() /
input_sync() on it. The timer is armed from appleir_raw_event() with
a HZ/8 (~125 ms) timeout on every keydown and key-repeat report. If a
key was pressed shortly before the device is disconnected, the timer
can fire after hid_hw_stop() has freed input_dev but before the
teardown drains it.
A simple reorder is not sufficient. Putting the timer drain first
still leaves a window where a USB URB completion (raw_event) running
during hid_hw_stop() can call mod_timer() and re-arm the timer, which
then fires after hidinput_disconnect() has freed input_dev. The same
URB-completion window also lets raw_event() reach key_up(), key_down()
and battery_flat() directly, all of which dereference
appleir->input_dev.
Introduce a 'removing' flag on struct appleir, gated by the existing
spinlock. appleir_remove() sets the flag under the lock and then
shuts down the timer with timer_shutdown_sync(), which both drains any
in-flight callback and permanently disables further mod_timer() calls.
appleir_raw_event() and key_up_tick() bail out early if the flag is
set, so no path can arm or run the timer, or dereference
appleir->input_dev, after remove() has started tearing down.
The keyrepeat and flatbattery branches of appleir_raw_event()
previously called into the input layer without holding the spinlock;
take it now so the flag check is well-defined. This incidentally
closes a pre-existing read-side race on appleir->current_key in the
keyrepeat branch.
This bug is structurally a sibling of commit 4db2af929279 ("HID:
appletb-kbd: fix UAF in inactivity-timer cleanup path") and has been
present since the driver was introduced. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: shrinker: fix shrinker_info teardown race with expansion
expand_shrinker_info() iterates all visible memcgs under shrinker_mutex,
including memcgs that have not finished ->css_online() yet.
Once pn->shrinker_info has been published, teardown must stay serialized
with expand_shrinker_info() until that memcg is either fully online or no
longer visible to iteration. Today alloc_shrinker_info() breaks that rule
by dropping shrinker_mutex before freeing a partially initialized
shrinker_info array, which may cause the following race:
CPU0 CPU1
==== ====
css_create
--> list_add_tail_rcu(&css->sibling, &parent_css->children);
online_css
--> mem_cgroup_css_online
--> alloc_shrinker_info
--> alloc node0 info
rcu_assign_pointer(C->node0->shrinker_info, old0)
alloc node1 info -> FAIL -> goto err
mutex_unlock(shrinker_mutex)
shrinker_alloc()
--> shrinker_memcg_alloc
--> mutex_lock(shrinker_mutex)
expand_shrinker_info
--> mem_cgroup_iter see the memcg
expand_one_shrinker_info
--> old0 = C->node0->shrinker_info
memcpy(new->unit, old0->unit, ...);
free_shrinker_info
--> kvfree(old0);
/* double free !! */
kvfree_rcu(old0, rcu);
The same problem exists later in mem_cgroup_css_online(). If
alloc_shrinker_info() succeeds but a subsequent objcg allocation fails,
the free_objcg -> free_shrinker_info() unwind path tears down the already
published pn->shrinker_info arrays without shrinker_mutex. The
expand_one_shrinker_info() can race with that teardown in the same way,
leading to use-after-free or double-free of the old shrinker_info.
Fix this by serializing shrinker_info teardown with shrinker_mutex, and by
keeping alloc_shrinker_info() error cleanup inside the locked section. |
| Kernel software installed and running inside a Guest VM may post improper commands to the GPU Firmware to trigger a read and/or write data outside the Guest's virtualised GPU memory.
The firmware uses data provided by the Guest VM to set up accesses to memory. It validated this before use, but a TOCTOU bug was present which allowed the earlier check results to be invalidated. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: igmp: remove multicast group from hash table on device destruction
When a device is destroyed under RTNL, ip_mc_destroy_dev() iterates through
the multicast list and calls ip_ma_put() on each membership, scheduling
them for RCU reclamation. However, they are not unlinked from the device's
multicast hash table (mc_hash).
Since the device remains published in dev->ip_ptr until after
ip_mc_destroy_dev() completes, concurrent RCU readers traversing mc_hash
can still locate and access the multicast group after its refcount is
decremented. If the RCU callback runs and frees the group while a reader is
accessing it, a use-after-free occurs.
Fix this by unlinking the multicast group from mc_hash using
ip_mc_hash_remove() before scheduling it for reclamation.
BUG: KASAN: slab-use-after-free in ip_check_mc_rcu+0x149/0x3f0
Read of size 4 at addr ffff888009bf1408 by task mausezahn/2276
Call Trace:
<IRQ>
dump_stack_lvl+0x67/0x90
print_report+0x175/0x7c0
kasan_report+0x147/0x180
ip_check_mc_rcu+0x149/0x3f0
udp_v4_early_demux+0x36d/0x12d0
ip_rcv_finish_core+0xb8b/0x1390
ip_rcv_finish+0x54/0x120
NF_HOOK+0x213/0x2b0
__netif_receive_skb+0x126/0x340
process_backlog+0x4f2/0xf00
__napi_poll+0x92/0x2c0
net_rx_action+0x583/0xc60
handle_softirqs+0x236/0x7f0
do_softirq+0x57/0x80
</IRQ>
Allocated by task 2239:
kasan_save_track+0x3e/0x80
__kasan_kmalloc+0x72/0x90
____ip_mc_inc_group+0x31a/0xa40
__ip_mc_join_group+0x334/0x3f0
do_ip_setsockopt+0x16fa/0x2010
ip_setsockopt+0x3f/0x90
do_sock_setsockopt+0x1ad/0x300
Freed by task 0:
kasan_save_track+0x3e/0x80
kasan_save_free_info+0x40/0x50
__kasan_slab_free+0x3a/0x60
__rcu_free_sheaf_prepare+0xd4/0x220
rcu_free_sheaf+0x36/0x190
rcu_core+0x8d9/0x12f0
handle_softirqs+0x236/0x7f0 |
| A vulnerability in `nltk.downloader` in nltk/nltk versions <= 3.9.4 allows for cross-package resource and model poisoning. The downloader extracts package archives into shared namespaces such as `corpora/` and `taggers/` instead of package-isolated roots, and validates package integrity only after the archive has been written and extracted. This design flaw enables one package to overwrite another package's trusted resources within the same namespace, making the changes immediately active through ordinary NLTK APIs. This issue persists across fresh interpreter restarts and can affect downstream workflows, including machine learning pipelines and reproducibility-sensitive environments. |
| Arm C1-Ultra, C1-Premium, Neoverse V3 & V3AE, Neoverse V2, Neoverse V1, Neoverse-N2, Neoverse-N1, Cortex-X925, Cortex-X4, Cortex-X3, Cortex-X2, Cortex-X1 & X1C, Cortex-A710, Cortex-A78, A78AE & A78C, Cortex-A77, Cortex-A76 & A76A may allow writes to resources owned by a higher exception level. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: synchronize DMA teardown
dmaengine_terminate_all() does not wait for a running callback, so the TX
callback can still touch the TX buffer after it is freed. The RX poll
timer reads the RX buffers without the port lock.
Switch to dmaengine_terminate_sync() and delete the RX timer before
freeing the buffers. |
| Divide-by-zero in Xpdf 4.06 (and earlier), when a glyph in a Type 3 font has a zero height. |
| Race condition in V8 in Google Chrome prior to 152.0.7977.82 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| In the Linux kernel, the following vulnerability has been resolved:
NTB: epf: Avoid calling pci_irq_vector() from hardirq context
ntb_epf_vec_isr() calls pci_irq_vector() in hardirq context to derive
the vector number. pci_irq_vector() calls msi_get_virq() that takes a
mutex and can therefore trigger "scheduling while atomic" splats:
BUG: scheduling while atomic: kworker/u33:0/55/0x00010001
...
Call trace:
...
schedule+0x38/0x110
schedule_preempt_disabled+0x28/0x50
__mutex_lock.constprop.0+0x848/0x908
__mutex_lock_slowpath+0x18/0x30
mutex_lock+0x4c/0x60
msi_domain_get_virq+0xe8/0x138
pci_irq_vector+0x2c/0x60
ntb_epf_vec_isr+0x28/0x120 [ntb_hw_epf]
__handle_irq_event_percpu+0x70/0x3a8
handle_irq_event+0x48/0x100
handle_edge_irq+0x100/0x1c8
...
Cache the Linux IRQ number for vector 0 when vectors are allocated and
use it as a base in the ISR. Running the ISR in a threaded IRQ handler
would also avoid the problem, but that would be unnecessary here. |
