| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: core: Add lock to usb_wakeup_notification()
Add a spin lock to usb_wakeup notification to prevent a race condition
with dereferencing freed memory. This could be hit by the xHCI driver as
it calls this function from an IRQ and could race with the
hub_disconnect() function, which properly grabs this lock to protect the
state of the device. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: sun8i-ss - Remove crypto_rng interface
Since the crypto_rng interface for hardware PRNGs is unused and is
redundant with hwrng and the actual Linux RNG, it's being phased out.
Most drivers for it were already removed. Go ahead and remove the
sun8i-ss support which is one of the only remaining ones.
As usual for crypto_rng, this driver was also buggy: its ->generate()
function had a use-after-free vulnerability due to using
wait_for_completion_interruptible_timeout() without handling shutting
down the DMA operation if a signal is sent. Also, it had a buffer
overread bug in the line 'memcpy(ctx->seed, d + dlen, ctx->slen);'.
There's no point in fixing these bugs separately only to remove the code
anyway, so this commit is marked with Fixes and Cc stable. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: sun8i-ce - Remove crypto_rng interface
Since the crypto_rng interface for hardware PRNGs is unused and is
redundant with hwrng and the actual Linux RNG, it's being phased out.
Most drivers for it were already removed. Go ahead and remove the
sun8i-ce support which is one of the only remaining ones.
Note that the sun8i-ce support for hwrng remains in place. That is the
interface that actually matters.
As usual for crypto_rng, this driver was also buggy: its ->generate()
function had a use-after-free vulnerability due to using
wait_for_completion_interruptible_timeout() without handling shutting
down the DMA operation if a signal is sent. There's no point in fixing
this separately only to remove the code anyway, so this commit is marked
with Fixes and Cc stable. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: keep the last remote linked during FDB flush
A non-nexthop FDB entry is expected to have at least one remote while it
remains reachable through the FDB hash table. A filtered bulk flush
violates this invariant when every remote matches: It unlinks the last
remote in vxlan_fdb_dst_destroy() and only afterwards tells vxlan_flush()
to destroy the parent FDB entry.
An RCU reader can find the parent during this interval.
first_remote_rcu() then applies list_entry_rcu() to the empty list head,
producing an invalid remote pointer that the receive learning path can
read from and write to.
When a matching remote is the sole remaining remote, leave it linked and
ask the caller to destroy the entire FDB entry. vxlan_fdb_destroy() keeps
the remote attached while sending the deletion notification and removing
the parent from the lookup structures. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: fix AO info use-after-free in tcp_ao_connect_init()
tcp_v4_connect() adds a SYN-SENT socket to the ehash before calling
tcp_connect(). If TCP-AO is configured, tcp_connect() first verifies that
a key matches the peer and the bound device's current L3 master.
tcp_ao_connect_init() later resolves the L3 master again and removes keys
which do not match it.
The socket lock does not stabilize the bound device's VRF membership.
Detaching the device from its VRF between the initial validation and the
L3-master calculation in tcp_ao_connect_init() can therefore make the
validation succeed while initialization observes the default L3 domain and
removes the only key. The subsequent AO lookup then fails, so the no-key
path clears tp->ao_info and frees it directly.
The receive path can find the socket in the ehash and load tp->ao_info
under RCU before acquiring the socket lock. A reader which loaded the old
pointer can thus continue into tcp_inbound_ao_hash() after the direct free.
The issue was found during a static audit of TCP-AO object lifetime. An
unprivileged reproducer in self-created user and network namespaces raced
connect() with detaching a veth from its VRF while sending TCP-AO segments.
It triggered the same KASAN report on two fresh boots:
BUG: KASAN: slab-use-after-free in tcp_inbound_ao_hash+0x585/0x19f0
Write of size 8 at addr ffff88800bf88128 by task tcp_ao_vrf_race/232
Call Trace:
tcp_inbound_ao_hash+0x585/0x19f0
tcp_inbound_hash+0x677/0xa80
tcp_v4_rcv+0x1c3e/0x3ab0
Allocated by task 235:
tcp_ao_alloc_info+0x43/0xf0
tcp_ao_add_cmd+0xdf7/0x13b0
do_tcp_setsockopt+0x168c/0x2640
Freed by task 235:
kfree+0x1b8/0x550
tcp_connect+0x252/0x4f00
tcp_v4_connect+0x1114/0x1720
The bad address is 40 bytes inside the freed 128-byte object, matching the
tcp_ao_info counters.key_not_found field. The two runs used 1000 attempts
each, reached the no-key path 366 and 411 times, and produced one and two
KASAN reports respectively. With this change, the same reproducer reached
the no-key path 366 times in 1000 attempts without a KASAN report or oops.
Use tcp_ao_destroy_sock() for the no-key path. It unpublishes the AO info,
updates the socket memory and static-key accounting, and defers the free
until after an RCU grace period.
Also drop the WARN_ON_ONCE() and its stale comment. The VRF detach race
makes the no-key state reachable during normal operation, so it is a
handled condition rather than an impossible assertion. On panic_on_warn
kernels the WARN would turn this handled race into a kernel panic. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_tcm: keep port count until LUN teardown completes
tcm_usbg_drop_nexus() permits session removal once tpg_port_count
reaches zero. However, usbg_port_unlink() currently decrements that
count from the fabric_pre_unlink() callback, before core_dev_del_lun()
waits for active se_lun references to drain.
If removal of the last LUN races a nexus removal, the latter can observe
a zero port count and call target_remove_session(). This frees
sess_cmd_map while an in-flight struct usbg_cmd, including its work item,
can still be accessed.
Overlapping the last-LUN unlink with nexus removal reproduces this
lifetime violation as a DEBUG_OBJECTS "free active" warning for
usbg_cmd_work, followed by a target-core BUG/Oops.
The generic target-core unlink path has no callback after
core_dev_del_lun() completes. Add an optional fabric_post_unlink()
callback and use it for the f_tcm port count. The count now remains
nonzero until core_dev_del_lun() has finished draining active LUN
references, preventing nexus removal from freeing the session during
command completion. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Fix CMD_SYNC use-after-free on teardown
arm_smmu_impl_remove() is registered as a devres action in
arm_smmu_impl_probe(), before arm_smmu_init_queues() allocates
smmu->cmdq.q.base. On a devres unwind, whether a failed probe or an
unbind, the queue is freed first and arm_smmu_impl_remove() then runs
tegra241_cmdqv_remove_vintf(), whose VINTF deinit issues a CMD_SYNC on
the freed memory.
Observed during testing with a QEMU hack that makes the VCMDQ fail to
enable, so the impl reset fails and probe aborts into the devres unwind:
platform NVDA200C:00: tegra241_cmdqv: VINTF0: VCMDQ0/LVCMDQ0: failed to enable, STATUS=0x00000000
platform NVDA200C:00: tegra241_cmdqv: VINTF0: VCMDQ0/LVCMDQ0: GERRORN=0x0, GERROR=0x4, CONS=0x0
platform NVDA200C:00: tegra241_cmdqv: VINTF0: VCMDQ0/LVCMDQ0: uncleared error detected, resetting
arm-smmu-v3 arm-smmu-v3.0.auto: failed to reset impl
arm-smmu-v3 arm-smmu-v3.0.auto: probe with driver arm-smmu-v3 failed with error -110
Unable to handle kernel paging request at virtual address ffff8000891e0098
...
Internal error: Oops: 0000000096000047 [#1] SMP
...
Call trace:
arm_smmu_cmdq_issue_cmdlist+0x320/0x6fc (P)
tegra241_vcmdq_hw_deinit+0x98/0x168
tegra241_vintf_hw_deinit+0x5c/0x1b0
tegra241_cmdqv_remove_vintf+0x34/0xec
tegra241_cmdqv_remove+0x40/0x9c
arm_smmu_impl_remove+0x20/0x30
devm_action_release+0x14/0x20
devres_release_all+0xa8/0x110
device_unbind_cleanup+0x18/0x84
really_probe+0x1f0/0x29c
Drop the VINTF deinit from tegra241_cmdqv_remove_vintf() so the unwind no
longer touches the freed queue. Quiesce the VINTFs earlier instead. Add a
device_disable() impl op and run it from arm_smmu_disable_action() while
the CMDQ is still up. That handles a live unbind. A failed reset is already
handled because tegra241_vintf_hw_init() deinits the VINTF on its own error
path. tegra241_cmdqv_remove_vintf() is also used by the iommufd viommu
destroy path, so quiesce there too. |
| A maliciously crafted PDF file, when parsed through Autodesk Revit, can force a Use-After-Free vulnerability. A malicious actor can leverage this vulnerability to cause a crash, disclose sensitive data, or execute arbitrary code in the context of the current process. |
| In the Linux kernel, the following vulnerability has been resolved:
futex/pi: Reject cross-mm private futex owners
A private futex key borrows the waiter's mm without taking an mm_users
reference. Nevertheless, attach_to_pi_owner() currently accepts an owner
from a different address space and copies the private key into the owner's
PI state.
When that owner exits, exit_pi_state_list() uses the saved key to find the
hash bucket and acquires a reference to the waiter's private hash. If the
last user of the waiter's mm exits concurrently, futex_hash_free() frees
the hash while the owner still uses its bucket and reference.
Prevent this by validating in attach_to_pi_owner() that, for private
futexes, the owner mm and waiter mm are the same. Perform the check with
the owner's pi_lock held and after validating owner::futex::state to
serialize against a concurrent PI-state exit cleanup.
[ tglx: Amended comment ] |
| In the Linux kernel, the following vulnerability has been resolved:
HID: magicmouse: do not keep a stale msc->input if no input is claimed
magicmouse_input_mapping() caches the first hid_input's input_dev in
msc->input while the report descriptor is parsed, and the rest of the
driver treats a non-NULL msc->input as proof that an input device was
registered.
That does not hold on the hid-input error path. If hidinput_connect()
fails -- for instance because input_register_device() returns an error --
it unwinds through hidinput_disconnect(), which frees every input_dev it
created, including the one cached in msc->input.
The failure does not abort the probe. hid_connect() only skips the claim:
if ((connect_mask & HID_CONNECT_HIDINPUT) && !hidinput_connect(hdev,
connect_mask & HID_CONNECT_HIDINPUT_FORCE))
hdev->claimed |= HID_CLAIMED_INPUT;
and the "device has no listeners" bailout below it does not fire for this
driver, which sets ->raw_event; on the USB Magic Mouse 2 / Magic Trackpad
2 paths hidraw and hiddev are claimed as well. hid_hw_start() therefore
returns 0 and magicmouse_probe() continues with msc->input pointing at
freed memory. Being non-NULL, it passes the "input not registered" check
in probe and the NULL checks in ->raw_event and ->event, so the next
input report dereferences freed memory.
Clear msc->input when the HID core did not claim an input device, so the
existing NULL checks cover this case as well. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: fix invalid free in LS IOD error path
nvmet_fc_alloc_ls_iodlist() advances iod while initializing the LS IOD
array. If an rqstbuf allocation or response buffer DMA mapping fails,
the unwind loop decrements iod past the start of the array. The final
kfree(iod) therefore frees an address before the allocated object.
This can be reproduced with nvme-fcloop and failslab by setting
fail-nth to 6 before creating a target port. KASAN reports:
BUG: KASAN: invalid-free in nvmet_fc_register_targetport
Free of addr ffff88816cf8ff48 by task nvmet_fail_nth/9552
Free the original allocation base stored in tgtport->iod instead. With
this fix applied, the same sysfs write with fail-nth=6 returns -ENOMEM
without any KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix use-after-free in ip6_finish_output2()
ip6_finish_output2() caches a pointer to the IPv6 destination
address (daddr) before invoking lwtunnel_xmit(). The LWT-BPF
transmit path or other encapsulation operations within
lwtunnel_xmit() can reallocate the skb head, freeing the memory
that daddr points to. When lwtunnel_xmit() returns
LWTUNNEL_XMIT_CONTINUE, the function continues to use the stale
daddr pointer to compute the nexthop and to look up or create the
neighbour entry. This results in a use-after-free read, which can
leak sensitive kernel data, pollute the neighbour table with
arbitrary values, misdirect traffic, or crash the system.
Fix this by re-fetching the IPv6 header and the destination
address pointer after lwtunnel_xmit() returns
LWTUNNEL_XMIT_CONTINUE, ensuring that the subsequent nexthop
computation and neighbour lookup operate on valid memory. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: uclogic: fix use-after-free of inrange_timer on remove
uclogic_remove() cancels the pen in-range timer and then stops the
device:
timer_delete_sync(&drvdata->inrange_timer);
hid_hw_stop(hdev);
timer_delete_sync() only guarantees the timer is idle at that instant.
uclogic_raw_event_pen() keeps delivering pen reports until hid_hw_stop()
stops the transport several lines later, and every report with
pen->inrange == UCLOGIC_PARAMS_PEN_INRANGE_NONE re-arms the timer:
mod_timer(&drvdata->inrange_timer, jiffies + msecs_to_jiffies(100));
A report landing between the timer_delete_sync() call and the transport
teardown in hid_hw_stop() re-arms inrange_timer after it was cancelled.
uclogic_remove() then returns and the devm drvdata is freed, while
hid_hw_stop() has already freed the input device drvdata->pen_input
points at, so when the timer fires ~100 ms later
uclogic_inrange_timeout() dereferences freed memory -- a use-after-free
in timer-softirq context.
Swapping the two calls is not a fix: stopping the device first frees
drvdata->pen_input via hidinput_disconnect() while the timer may still
be pending, so a timer already armed before removal fires on the freed
input device in the window before timer_delete_sync() runs.
Use timer_shutdown_sync() before hid_hw_stop() instead. It cancels the
timer, waits for a running callback while pen_input is still valid, and
prevents any further re-arming -- a later mod_timer() from an in-flight
report is silently ignored -- so the timer is provably dead before
hid_hw_stop() frees the inputs. This is the ordering the timer core
documents for this "timer re-armed from another path" teardown case. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: sensor: custom: Fix use-after-free in enable_sensor
enable_sensor_store() can call set_power_report_state(), which
dereferences sensor_inst->power_state and sensor_inst->report_state.
These pointers refer to entries in sensor_inst->fields.
Create the field attributes before exposing the enable_sensor sysfs
attribute, so enable_sensor cannot be accessed before the state it
depends on has been initialized.
On remove, delete enable_sensor before freeing the field attributes,
so a concurrent sysfs write cannot dereference freed memory through
power_state or report_state. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: scarlett2: Use a private URB for the notification endpoint
scarlett2_init_notify() used mixer->urb, which
snd_usb_mixer_status_create() allocates for the UAC2 status interrupt
endpoint and mixer.c manages. On a device with that endpoint, the
"already in use" check fires on the status URB and returns 0 for
success without doing anything. No notification URB is submitted, and
cmd_done is left zeroed because it is initialised past that check and
nowhere else. scarlett2_usb_init() then issues SCARLETT2_USB_INIT_1
and wait_for_completion_timeout() would crash adding to the zeroed
wait.head.
Use a separate URB in scarlett2_data, as done for FCP, and initialise
cmd_done in scarlett2_init_private(). mixer.c was also freeing the URB
in snd_usb_mixer_free() and resubmitting it in
snd_usb_mixer_activate(), so scarlett2 must now do both: add
scarlett2_cleanup_urb(), called from private_free and private_suspend,
and a private_resume callback to re-establish the URB after resume.
scarlett2_init_notify() is reached from there, and the URB kill path
in scarlett2_notify() completes cmd_done, leaving a stale count that
would satisfy the next command's wait before the device ACKs. Use
reinit_completion() to clear it.
Also free the URB if the transfer buffer allocation fails, and both if
usb_submit_urb() fails. Move scarlett2_init_notify() up next to
scarlett2_cleanup_urb() so scarlett2_init_private() can reference it
without a forward declaration. |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Fix race on the initial mm->futex.phash.ref allocation
futex_hash_allocate() allocates mm->futex.phash.ref without any locking.
Commit d9b05321e21e ("futex: Move futex_hash_free() back to __mmput()")
moved the allocation here and assumed that the process has just a single
thread at this point.
Commit ee9dce44362b ("futex: Drop CLONE_THREAD requirement for private
default hash alloc") widened need_futex_hash_allocate_default() to cover
any CLONE_VM clone, but left out vfork because the parent is suspended and
cannot race.
That no longer holds once vfork is nested. If a vfork child calls vfork
again and is then killed with SIGKILL, the parent is released from its
vfork wait and runs concurrently with the grandchild in the same mm.
Neither of them went through futex_hash_allocate_default().
When both call prctl(PR_FUTEX_HASH, PR_FUTEX_HASH_SET_SLOTS) at the same
time, each one sees mm->futex.phash.ref as NULL and stores its own percpu
counter. Only the last store survives. The counter stored first is no
longer reachable from the mm, so the references on it are not seen by
__futex_ref_atomic_end(). A private hash that still has references is then
considered dead and freed, and a task that still holds one of its buckets
writes into freed memory in futex_q_lock().
Store the counter once with cmpxchg() and let the loser free_percpu() its
own. The initial reference has to be taken before the store, otherwise
another task can install a private hash while the counter is still 0. |
| In the Linux kernel, the following vulnerability has been resolved:
futex/pi: Plug private futex exec() race
The check for private futexes whether the waiter's mm, which is stored in
the futex_key and copied into the pi_state, is the same as the owner's mm
is not sufficient for exec(). exec() has a gap where the mm check fails to
give the correct answer:
exec()
...
exec_release_mm()
futex_exec_release()
tsk::futex::exit_state = EXITING;
cleanup_robust_list();
1) tsk::futex::exit_state = OK;
...
old_mm = tsk::mm;
2) tsk::mm = ->mm;
Between #1 and #2 the check for the mm is wrong as that mm is about to be
swapped out and eventually freed.
Plug this gap by:
1) Setting tsk::futex::exit_state to FUTEX_STATE_DEAD in
futex_exec_release()
2) Setting tsk::futex::exit_state to FUTEX_STATE_OK after
the mm has been switched.
From a futex point of view the task is dead after it finished the robust
list cleanup up to the point where it sets the state to OK again. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: serialize mode sysfs access with lock_fb_info()
show_mode(), show_modes(), and store_mode() access fb_info->modelist
and fb_info->mode without holding lock_fb_info(). store_modes() takes
lock_fb_info() while replacing the modelist and freeing the old one.
A concurrent reader or writer can load a pointer to an old modelist
entry before store_modes() frees it, then dereference freed memory or
store a stale freed pointer in fb_info->mode.
Take lock_fb_info() in show_mode(), show_modes(), and store_mode() to
serialize with store_modes(). In show_mode(), copy the mode to the
stack and format after dropping the lock. In store_mode(), split
activate() into a _locked variant to avoid double-locking, and hold
the locks for the modelist walk, mode conversion, activation, and
fb_info->mode assignment together. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix accept list UAF during suspend
hci_update_event_filter_sync() walks hdev->accept_list while sending a
synchronous HCI command for each remote-wakeup device. The suspend path
holds hdev->req_lock, but accept-list updates are serialized by hdev->lock.
Consequently, remove_device() can free the current list entry during the
controller wait.
The following interleaving causes the use-after-free:
hci_update_event_filter_sync() remove_device()
fetch accept-list entry
hci_set_event_filter_sync()
wait for controller response hci_dev_lock()
list_del()
kfree()
hci_dev_unlock()
read the freed list.next
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_suspend_sync+0x835/0x910
Read of size 8 at addr ffff88810bec8440 by task kworker/0:1/10
Workqueue: events vhci_suspend_work
Call Trace:
hci_suspend_sync+0x835/0x910
hci_suspend_dev+0x182/0x450
process_one_work+0x661/0x1090
worker_thread+0x45b/0xd10
Allocated by task 86:
hci_bdaddr_list_add_with_flags+0x1a8/0x400
add_device+0x381/0x820
hci_sock_sendmsg+0x1033/0x1ea0
Freed by task 91:
kfree+0x131/0x3c0
remove_device+0x429/0xb70
hci_sock_sendmsg+0x1033/0x1ea0
Snapshot the remote-wakeup addresses under hdev->lock. Release the lock
before sending HCI commands. Clear the controller event filter before
building the snapshot, and skip allocation and the second list traversal
when there are no matching entries. This preserves the original filter
and scan-state updates without retaining an accept-list node across a
controller wait. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: lg-g15: cancel pending work on remove to fix a use-after-free
lg_g15_data is allocated with devm and holds a work item. The report
handlers schedule that work straight from device input.
lg_g15_event() and lg_g15_v2_event() do it on the backlight cycle key,
and lg_g510_leds_event() does it too. The worker dereferences the
lg_g15_data back through container_of.
The driver had no remove callback and never cancelled the work. So if a
report scheduled the work and the keyboard was then unplugged, devres
freed lg_g15_data while the work was still pending or running, and the
worker touched freed memory. This is a use-after-free. It is reachable
as a race on device unplug.
Add a remove callback that cancels the work before devres frees the
state. g15->work is only initialized for the models that schedule it
(G15, G15 v2, G510). The G13 and Z-10 leave it zeroed, so guard the
cancel on g15->work.func to avoid cancelling a work that was never set
up. The g15 NULL test mirrors the one already in lg_g15_raw_event(). |
