| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: fix dst corruption in same register operation
For lshift and rshift, the shift operations are performed in a loop over
32-bit words. The loop calculates the shifted value and write it to dst,
and then immediately reads from src to calculate the carry for the next
iteration. Because src and dst could point to the same memory location,
the carry is incorrectly calculated using the newly modified dst value
instead of the original src value.
Adding a temporary local variable to cache the original value before
writing to dst and using it for the carry calculation solves the
problem. In addition, partial overlap is rejected from control plane for
all kind of operations including byteorder. This was tested with the
following bytecode:
table test_table ip flags 0 use 1 handle 1
ip test_table test_chain use 3 type filter hook input prio 0 policy accept packets 0 bytes 0 flags 1
ip test_table test_chain 2
[ immediate reg 1 0x44332211 0x88776655 ]
[ bitwise reg 1 = ( reg 1 << 0x08000000 ) ]
[ cmp eq reg 1 0x66443322 0x00887766 ]
[ counter pkts 0 bytes 0 ]
ip test_table test_chain 4 3
[ immediate reg 1 0x44332211 0x88776655 ]
[ bitwise reg 1 = ( reg 1 << 0x08000000 ) ]
[ cmp eq reg 1 0x55443322 0x00887766 ]
[ counter pkts 21794 bytes 1917798 ] |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix clone_alias() to use the original device's devid
Currently clone_alias() assumes first argument (pdev) is always the
original device pointer. This function is called by
pci_for_each_dma_alias() which based on topology decides to send
original or alias device details in first argument.
This meant that the source devid used to look up and copy the DTE
may be incorrect, leading to wrong or stale DTE entries being
propagated to alias device.
Fix this by passing the original pdev as the opaque data argument to
both the direct clone_alias() call and pci_for_each_dma_alias(). Inside
clone_alias(), retrieve the original device from data and compute devid
from it. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix signededness bug in smb_direct_prepare_negotiation()
smb_direct_prepare_negotiation() casts an unsigned __u32 value
from sp->max_recv_size and req->preferred_send_size to a signed
int before computing min_t(int, ...). A maliciously provided
preferred_send_size of 0x80000000 will return as smaller than
max_recv_size, and then be used to set the maximum allowed
alowed receive size for the next message.
By sending a second message with a large value (>1420 bytes)
the attacker can then achieve a heap buffer overflow.
This fix replaces min_t(int, ...) with min_t(u32) |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix incorrect pruning due to atomic fetch precision tracking
When backtrack_insn encounters a BPF_STX instruction with BPF_ATOMIC
and BPF_FETCH, the src register (or r0 for BPF_CMPXCHG) also acts as
a destination, thus receiving the old value from the memory location.
The current backtracking logic does not account for this. It treats
atomic fetch operations the same as regular stores where the src
register is only an input. This leads the backtrack_insn to fail to
propagate precision to the stack location, which is then not marked
as precise!
Later, the verifier's path pruning can incorrectly consider two states
equivalent when they differ in terms of stack state. Meaning, two
branches can be treated as equivalent and thus get pruned when they
should not be seen as such.
Fix it as follows: Extend the BPF_LDX handling in backtrack_insn to
also cover atomic fetch operations via is_atomic_fetch_insn() helper.
When the fetch dst register is being tracked for precision, clear it,
and propagate precision over to the stack slot. For non-stack memory,
the precision walk stops at the atomic instruction, same as regular
BPF_LDX. This covers all fetch variants.
Before:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs=r2 stack= before 2: (b7) r2 = 0
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit
After:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs= stack=-8 before 2: (b7) r2 = 0
mark_precise: frame0: regs= stack=-8 before 1: (7b) *(u64 *)(r10 -8) = r1
mark_precise: frame0: regs=r1 stack= before 0: (b7) r1 = 8
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit |
| Incorrect boundary conditions in the Layout: Scrolling and Overflow component. This vulnerability was fixed in Firefox 159, Firefox ESR 153.6, Thunderbird 159, and Thunderbird 153.6. |
| An incorrect calculation in Decimal128 string parsing in the MongoDB C Driver can accept certain over-precision inputs containing leading zeros instead of rejecting them. This produces a value different from the supplied text. An actor who can provide a decimal string to an embedding application, including through Extended JSON parsing, can cause the application to store or use an incorrect numeric value. |
| FFmpeg before commit b4c199c contains an incorrect integer narrowing conversion in the AV1 RTP packetizer (libavformat/rtpenc_av1.c). The OBU size is cast to long before comparison against the remaining frame size. On targets where long is 32 bits, including 64-bit Windows, sufficiently large OBU size values are sign-flipped by the narrowing cast, producing a negative value that passes the payload size check. This allows an oversized OBU to bypass the safety bound on affected platforms, leading to out-of-bounds memory access when the oversized value is subsequently used as a copy length. |
| Netty netty-tcnative before 2.0.84.Final contains a denial of service vulnerability in the tcn_write_to_bytebuffer BIO write callback that overreports bytes consumed. Remote TLS 1.3 peers can provoke queued post-handshake records like NewSessionTicket or KeyUpdate to truncate flights, fail connections, or abort the JVM process. |
| In the Linux kernel, the following vulnerability has been resolved:
accel: ethosu: Don't read the U65 rounding mode as a storage mode
Bits 15:14 of NPU_SET_{IFM,OFM}_PRECISION select the activation storage
mode on U85 only. On U65 the same field holds the rounding mode, and the
command stream parser has read it as a storage mode since the driver was
added.
That went unnoticed while unknown values fell through the switch, but
now that they are rejected, every U65 command stream that asks for
natural rounding (2) fails CMDSTREAM_BO_CREATE with -EINVAL. Mesa emits
it for average pooling, concatenation, split, unpack, strided slice, LUT
and argmax, which is 72 failures of the Teflon test suite on an i.MX93.
Truncating rounding (1) is misread as well: it picks the two-tile
address path and computes a bogus feature map size from tile bases the
command stream never set.
Read the field as a storage mode only on the hardware where it is one. |
| Incorrect conversion between numeric types in Windows TCP/IP allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Infer zext_dst based on static register liveness analysis
As reported in the thread [1], the verifier's 32-bit operations zero
extension logic is broken. This logic is responsible for correct
semantics of 32-bit operations on s390 architecture.
According to BPF semantics, operation `w1 += 1` is supposed to zero
extend the upper half of the register `r1`. On s390 the JIT relies on
the verifier emitting explicit zero extension before such operations.
The verifier attempts to minimize the amount of zero extensions
inserted by tracking whether upper halves of the 64-bit registers are
ever used. Previously such tracking worked as follows:
- bpf_reg_state->subreg_def field was set by do_check_insn()
for each operation defining lower but not the upper halves
of the register.
- Whenever an operation reading the whole register was verified,
the verifier checked register's subreg_def and set
bpf_insn_aux_data->zext_dst flag as true via a call to
mark_insn_zext() function.
- After the verification was complete, a special pass
bpf_opt_subreg_zext_lo32_rnd_hi32() extended 32-bit operations
with bpf_insn_aux_data->zext_dst set as true by adding
explicit zero extension.
Note that the logic above relies on bpf_reg_state->subreg_def,
which is a property of a current verifier state.
Before the commit [2] two additional steps happened:
- The verifier tracked upper and lower register halves' liveness as
flags REG_LIVE_READ{32,64} in bpf_reg_state->live.
- The function propagate_liveness() called mark_insn_zext()
in order to transfer the knowledge about which registers have
their upper halves alive (and thus might require zero extension).
The commit [2] removed the two steps described above,
hence making possible a situation like below:
- The register's upper half is set and is used on some verification
path P1 and the register happens not to be marked as precise.
- The checkpoint C is created while processing some instruction
between register initialization and usage.
- On some other verification path P2 the register's upper half is not
initialized and that path ends hitting the checkpoint C.
- In such a case the register's initialization on path P2 would lack
zext_dst mark, making it possible for the program to inject
an arbitrary value in the register's upper half.
This commit replaces subreg_def based logic with computing zext_dst
statically, as a part of the bpf_compute_live_registers() analysis:
- The analysis now tracks usage of upper and lower halves of the
registers separately.
- If some instruction defines a 32-bit subregister, but not the whole
register, *and* the upper half of the register is alive after that
instruction, the instruction is marked as zext_dst.
There is one notable drop in precision: whenever a BPF subprogram is
called, all 64 bits of parameter registers are presumed to be used.
The assumption is that such a drop in precision would not inflict
a noticeable performance penalty.
[1] https://lore.kernel.org/bpf/CAGKGUv=sOuqQtA1Ub-5JXfA4FPosJFYKAQE4B79cK+P1erxqtg@mail.gmail.com/
[2] commit 107e16979905 ("bpf: disable and remove registers chain based liveness") |
| Incorrect Calculation vulnerability in VillaTheme CURCY woo-multi-currency allows Integer Attacks.This issue affects CURCY: from n/a through 2.2.17. |
| In the Linux kernel, the following vulnerability has been resolved:
af_packet: Don't cast tpacket_hdr.tp_len to int in tpacket_parse_header().
syzbot reported BUG() in sock_sendmsg_nosec(). [0]
The problem is that tpacket_parse_header() casts user-provided
tpacket_hdr.tp_len, which is u32, to int.
If the length is larger than INT_MAX, the following condition
in tpacket_parse_header() passes,
if (unlikely(tp_len > size_max))
and any negative value can be returned to the caller, up to
sock_sendmsg_nosec().
The repro set tpacket_hdr.tp_len to 0xfffffdef, which is cast
to -EIOCBQUEUED (-529), triggering BUG() in sock_sendmsg_nosec().
*(uint64_t*)0x200000000008 = 0xfffffdef;
...
syscall(__NR_write, /*fd=*/r[0], /*buf=*/0x200000000000ul, /*count=*/1ul);
Let's define the local tp_len as u32 in tpacket_parse_header().
[0]:
kernel BUG at net/socket.c:803!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 5628 Comm: syz-executor176 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/24/2026
RIP: 0010:sock_sendmsg_nosec+0x145/0x180 net/socket.c:803
Code: 06 67 48 0f b9 3a eb 95 e8 e8 3a 22 f8 48 89 df 4c 89 f6 4c 89 e2 4d 89 fb 2e e8 32 a5 5c 16 e9 51 ff ff ff e8 cc 3a 22 f8 90 <0f> 0b e8 c4 3a 22 f8 48 83 c3 18 48 89 d8 48 c1 e8 03 42 80 3c 28
RSP: 0018:ffffc90003aefb48 EFLAGS: 00010293
RAX: ffffffff89a578d4 RBX: ffff8880764c67c0 RCX: ffff88807fb23e80
RDX: 0000000000000000 RSI: 00000000fffffdef RDI: 00000000fffffdef
RBP: 00000000fffffdef R08: ffffc90003aef747 R09: 1ffff9200075dee8
R10: dffffc0000000000 R11: fffff5200075dee9 R12: 0000000000000001
R13: dffffc0000000000 R14: ffffc90003aefbc0 R15: ffffffff8aac4310
FS: 000055559101b400(0000) GS:ffff888124ce0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000200000000210 CR3: 0000000073dca000 CR4: 00000000003526f0
Call Trace:
<TASK>
__sock_sendmsg net/socket.c:815 [inline]
sock_write_iter+0x2de/0x3e0 net/socket.c:1266
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x612/0xba0 fs/read_write.c:687
ksys_write+0x150/0x270 fs/read_write.c:739
do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline]
do_syscall_64+0x166/0x520 arch/x86/entry/syscall_64.c:84
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f173130ecb9
Code: c0 79 93 eb d5 48 8d 7c 1d 00 eb 99 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 d8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd67e44248 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000200000000000 RCX: 00007f173130ecb9
RDX: 0000000000000001 RSI: 0000200000000000 RDI: 0000000000000003
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffd67e44388
R13: 0000000000000002 R14: 00002000000000c0 R15: 0000000000000002
</TASK> |
| IBM MQ could allow an authenticated attacker to cause a denial of service through a specially crafted message that triggers excessive memory operations during character set conversion. |
| A numeric-type conversion flaw in the BSON handling library of the MongoDB C# Driver allows an out-of-range binary subtype value supplied through untrusted textual input to bypass the library's binary-element integrity checks. When such a value is later encoded, it is narrowed to a smaller wire representation, producing binary elements that misdeclare their type or length. An unauthenticated party able to supply text parsed by an affected application can cause it to emit and persist malformed binary data, which subsequent readers either reject with an error or silently interpret as shorter than the data that was validated. |
| libssh2 1.11.1, fixed in commit 97acf3d, contains an out-of-bounds write vulnerability in ssh2_transport_read() that fails to enforce upper bounds on packet_length field. Remote attackers can send crafted SSH packets with excessively large packet_length values to corrupt heap memory and achieve remote code execution. |
| As part of Cisco's ongoing commitment to proactive security and product quality, the Cisco owned Open Source Snort 3 Software engineering team has conducted a comprehensive internal security review. This review resulted in software hardening releases that address multiple internally discovered vulnerabilities.
The vulnerabilities tracked by CVE-2026-20236 are related to issues concerning incorrect calculation that are grouped under the Common Weakness Enumeration (CWE) Base CWE-682. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: sockmap: fix tail fragment offset in bpf_msg_push_data
When bpf_msg_push_data() inserts data in the middle of a scatterlist
entry, it splits the original entry into a left fragment and a right
fragment.
The right fragment offset is page-local, but the code advances it with
`start`, which is the message-global insertion point. For inserts into a
non-first SG entry, this over-advances the offset and leaves the split
layout inconsistent.
Advance the right fragment offset by the fragment-local delta,
`start - offset`, which matches the length removed from the front of the
original entry. |
| Vyper 0.3.4 through 0.5.0b1 computes the remaining blueprint size in create_from_blueprint by uint256 subtraction without first checking that code_offset is below the blueprint's code size, so a huge offset wraps to a small positive value. An attacker controlling code_offset can make a factory deploy contracts with no runtime code, potentially trapping ETH and tokens. |
| Vyper 0.3.8 through 0.5.0b1 contains an optimizer miscompilation in which (msg.value | K) or (len(msg.data) | K), where K is any nonzero integer literal, is compiled to the constant 1 when used as a ternary expression branch under -O gas (the default) or -O codesize. Affected contracts use the wrong value in storage writes, arithmetic, indexes, return values, or events without warning or revert, which can record deposits incorrectly and lock funds. |
