| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HID: bpf: Fix hid_bpf_get_data() range check
hid_bpf_get_data() returns a pointer into the HID-BPF context data when
the caller-provided offset and size fit inside ctx->allocated_size.
The current check adds rdwr_buf_size and offset before comparing the
result against ctx->allocated_size. Since both values are unsigned, a
very large size can wrap the sum below ctx->allocated_size and make the
helper return a pointer even though the requested range is not contained
in the backing buffer.
Use check_add_overflow() to reject wrapped range ends before comparing
the requested range end against ctx->allocated_size. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to cause a denial of service due to a stack-based buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: fix 32-bit integer overflow in qrtr_endpoint_post()
qrtr_endpoint_post() validates an incoming packet with
if (!size || len != ALIGN(size, 4) + hdrlen)
goto err;
where size comes from the wire. On 32-bit, size_t is 32 bits and
ALIGN(size, 4) wraps to 0 for size >= 0xfffffffd, so the check
passes and skb_put_data(skb, data + hdrlen, size) writes past the
hdrlen-sized skb and oopses the kernel. 64-bit is unaffected.
This is the 32-bit residual of ad9d24c9429e2 ("net: qrtr: fix OOB
Read in qrtr_endpoint_post"), which fixed only the 64-bit case.
Reject any size that cannot fit the buffer before the ALIGN. |
| A vulnerability was detected in GL.iNet A1300, AX1800, AXT1800, MT2500, MT3000, MT6000, X3000 and XE3000 4.8.x. This issue affects some unknown processing of the file /usr/bin/gl_nas_sys of the component NAS Command Service. The manipulation results in os command injection. The attack may be launched remotely. Upgrading to version 4.9.0 is capable of addressing this issue. It is suggested to upgrade the affected component. The vendor explains: "After our investigation, we have confirmed that the vulnerability described (...) does indeed exist." |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix BPF_PROG_QUERY OOB write and cgroup backward compat
BPF_PROG_QUERY writes back the 'query.revision' field unconditionally to
userspace. If userspace passes a smaller 'bpf_attr' structure (e.g. 40
bytes, which was the layout before the addition of 'query.revision'),
the kernel performs an out-of-bounds write.
Fix this by propagating the user-provided attribute size 'uattr_size'
down to the cgroup query handlers, and conditionally skipping writing
the revision field to userspace when the provided buffer size is
insufficient.
query.revision in bpf_mprog_query is structurally identical to the
cgroup case: a late tail field, written unconditionally.
But the backward-compat hazard is not the same.
The min-historical-size test is per command, and bpf_mprog_query only
serves attach types that were born with revision in the struct:
- tcx_prog_query -> BPF_TCX_INGRESS/EGRESS
- netkit_prog_query -> BPF_NETKIT_PRIMARY/PEER
tcx, netkit, the revision field, and bpf_mprog_query itself all landed in
the same v6.6 merge window (053c8e1f235d added the mprog query API +
revision; tcx in e420bed02507, netkit in 35dfaad7188c). There has never
been a tcx/netkit BPF_PROG_QUERY userspace that doesn't know about
revision. So for these commands the minimum legitimate struct already
covers offset 56-64 — no old binary can be broken here.
Contrast with cgroup: BPF_PROG_QUERY on cgroup attach types shipped in
2017; revision write-back was bolted on years later (120933984460). That
path has a real population of pre-revision callers. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to execute arbitrary code due to a heap-based buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
ixgbe: do not configure xps for XDP queues
netif_set_xps_queue() should not be called for an XDP Tx queue, since such
queues are not netdev-exposed. On systems with number of CPUs >=64, on E610
adapter, netdev is configured with maximum number queue pairs being 63
(due to MSI-X assignment), but configuring XDP results in 64 XDP queues.
So, during XDP program load, when netif_set_xps_queue() is called for the
last XDP queue, we get a WARNING with a call trace and KASAN report
afterwards (if enabled).
[ 2012.699800] WARNING: net/core/dev.c:2854 at __netif_set_xps_queue+0x116a/0x1e40, CPU#36: xdpsock/103668
[...]
[ 2012.700029] RIP: 0010:__netif_set_xps_queue+0x116a/0x1e40
[ 2012.700035] Code: b6 34 06 48 89 f8 83 e0 07 83 c0 01 40 38 f0 7c 09 40 84 f6 0f 85 03 0a 00 00 0f b7 44 24 40 66 43 89 44 6a 18 e9 01 fb ff ff <0f> 0b e9 f2 ee ff ff 44 8b 44 24 44 45 85 c0 74 50 4d 85 e4 0f 84
[ 2012.700040] RSP: 0018:ffff8882369aeb28 EFLAGS: 00010246
[ 2012.700046] RAX: 0000000000000000 RBX: 000000000000003f RCX: 0000000000000000
[ 2012.700050] RDX: 1ffff1111da3d891 RSI: ffff888120e34250 RDI: ffff8888ed1ec488
[ 2012.700054] RBP: ffff888913281560 R08: 0000000000000000 R09: ffff8888ed1ec000
[ 2012.700058] R10: ffff8888a2e83180 R11: 0000000000000000 R12: 0000000000007fa8
[ 2012.700061] R13: 000000000000003f R14: ffff888120e34854 R15: ffff8889132817c8
[ 2012.700065] FS: 00007fc8ea9ff740(0000) GS:ffff88884cefe000(0000) knlGS:0000000000000000
[ 2012.700069] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2012.700073] CR2: 00007f81c8000020 CR3: 00000002299f8006 CR4: 00000000007726f0
[ 2012.700077] PKRU: 55555554
[ 2012.700080] Call Trace:
[ 2012.700084] <TASK>
[ 2012.700087] ? ktime_get+0x61/0x150
[ 2012.700097] ? usleep_range_state+0x133/0x1b0
[ 2012.700108] ? __pfx_usleep_range_state+0x10/0x10
[ 2012.700114] netif_set_xps_queue+0x31/0x50
[ 2012.700119] ixgbe_configure_tx_ring+0x472/0x920 [ixgbe]
[...]
[ 2012.700486] ixgbe_xdp+0x38f/0x750 [ixgbe]
[...]
[ 2012.701094] BUG: KASAN: slab-out-of-bounds in __netif_set_xps_queue+0x1ac5/0x1e40
[ 2012.701100] Write of size 4 at addr ffff88888d43cff8 by task xdpsock/103668
Skip XPS configuration for XDP Tx queues. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a local attacker to execute arbitrary code due to an out-of-bounds write. |
| Exposed methods allow authenticated users to create and execute arbitrary JavaScript code on the server. The scripts execute with full access, enabling complete system compromise as commands are executed as root. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix out-of-bounds clear_bit in ath12k_mac_dp_peer_cleanup()
ath12k_mac_dp_peer_cleanup() clears the ML peer ID slot on the
free_ml_peer_id_map bitmap by indexing it with dp_peer->peer_id. That is
wrong: dp_peer->peer_id for an MLO peer always carries the
ATH12K_PEER_ML_ID_VALID bit (BIT(13)), so clear_bit() is invoked with
index >= 0x2000, which is far outside the bitmap of ATH12K_MAX_MLO_PEERS
(256) bits and corrupts memory adjacent to ah->free_ml_peer_id_map. The
intended bitmap entry also never gets cleared, so subsequent
ath12k_peer_ml_alloc() calls eventually run out of IDs.
The ID without the VALID bit is what ath12k_peer_ml_alloc() returned and
is stored in ahsta->ml_peer_id. Use that instead.
While there, also reset ahsta->ml_peer_id to ATH12K_MLO_PEER_ID_INVALID so
the bitmap and ahsta->ml_peer_id stay in sync.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3 |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to execute arbitrary code due to a buffer overflow. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to execute arbitrary code due to a buffer overflow. |
| IBM i 7.6, 7.5, 7.4, and 7.3 s vulnerable to a buffer overflow from improperly validating client data. By sending malformed requests to one of the host servers, a remote attacker could leverage this vulnerability to cause a denial-of-server (DoS) for that server. |
| In Roundcube Webmail before 1.6.18 and 1.7.x before 1.7.3, the cmd_learn driver of the markasjunk plugin is subject to remote code execution via crafted placeholder replacement values. This issue only affects Roundcube instances using the markasjunk plugin with its cmd_learn driver. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci: validate codec capability element length
Read Local Codec Capabilities returns a sequence of capability elements.
Each element starts with a one-byte length followed by that many payload
bytes.
hci_read_codec_capabilities() checks that the skb contains the length
byte, but then validates only caps->len against the remaining skb
length. A malformed controller response with one remaining byte and
caps->len set to one passes that check even though the element needs two
bytes. The parser then records a two-byte capability and copies one
byte beyond the advertised response payload into the codec list.
Validate the full element size, including the length byte, before adding
it to the accumulated capability length. This preserves all well-formed
capability elements and drops only truncated controller responses. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to execute arbitrary code due to a stack-based buffer overflow. |
| IBM i 7.6, 7.5, 7.4, and 7.3 is vulnerable to privilege escalation via Navigator for i. An authenticated user could elevate privileges to a root user to execute commands. |
| A heap out-of-bounds write vulnerability in the Linux kernel's Performance Events system component can be exploited to achieve local privilege escalation.
A perf_event's read_size can overflow, leading to an heap out-of-bounds increment or write in perf_read_group().
We recommend upgrading past commit 382c27f4ed28f803b1f1473ac2d8db0afc795a1b. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: fix OOB access from firmware tx status queue ID
ath_tx_edma_tasklet() accesses sc->tx.txq[ts.qid] where ts.qid is a
4-bit hardware field (0-15), but the txq array only has
ATH9K_NUM_TX_QUEUES (10) entries. A qid >= 10 causes an OOB array
access.
Add a bounds check on ts.qid before using it as an array index. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix KASAN slab-out-of-bounds in amdgpu_coredump ring dump
The ring content dump in amdgpu_coredump() uses two separate loops over
adev->rings[]: the first counts rings with unsignalled fences to size
the allocation, and the second copies ring data into the allocated
buffers.
Both loops use the same condition to skip rings:
atomic_read(&ring->fence_drv.last_seq) == ring->fence_drv.sync_seq
Because last_seq is an atomic that is updated concurrently by the fence
signalling path, additional rings may appear unsignalled in the second
loop that were signalled during the first. When this happens, idx
exceeds the allocated ring_count and the store to coredump->rings[idx]
writes past the end of the kcalloc-ed buffer.
This was found during IGT stressful test amd_queue_reset which
triggers random GPU resets. The OVERSIZE subtest
(CMD_STREAM_EXEC_INVALID_PACKET_LENGTH_OVERSIZE on GFX ring) provokes
a ring timeout and subsequent coredump, which hits the race between
the counting and copying loops. The failure is non-deterministic and
depends on fence signalling timing during the reset.
KASAN log:
BUG: KASAN: slab-out-of-bounds in amdgpu_coredump+0x1274/0x12f0 [amdgpu]
Write of size 4 at addr ffff888106154258 by task kworker/u128:5/23625
CPU: 16 UID: 0 PID: 23625 Comm: kworker/u128:5 Not tainted 6.19.0+ #35
Workqueue: amdgpu-reset-dev drm_sched_job_timedout [gpu_sched]
Call Trace:
<TASK>
dump_stack_lvl+0xa5/0x110
print_report+0xd1/0x660
kasan_report+0xf3/0x130
__asan_report_store4_noabort+0x17/0x30
amdgpu_coredump+0x1274/0x12f0 [amdgpu]
amdgpu_job_timedout+0xef0/0x16c0 [amdgpu]
drm_sched_job_timedout+0x194/0x5c0 [gpu_sched]
process_one_work+0x84b/0x1990
worker_thread+0x6b8/0x11b0
</TASK>
Allocated by task 23625:
kasan_save_stack+0x39/0x70
__kasan_kmalloc+0xc3/0xd0
__kmalloc_noprof+0x2ec/0x910
amdgpu_coredump+0x5c5/0x12f0 [amdgpu]
amdgpu_job_timedout+0xef0/0x16c0 [amdgpu]
The buggy address belongs to the object at ffff888106154200
which belongs to the cache kmalloc-rnd-09-96 of size 96
The buggy address is located 16 bytes to the right of
allocated 72-byte region [ffff888106154200, ffff888106154248)
72 bytes = 3 * sizeof(struct amdgpu_coredump_ring), so ring_count was 3
but idx reached 3+, writing ring_index (at struct offset 16) 16 bytes
past the allocation.
Fix by adding an idx < ring_count guard to the copy loop so it cannot
exceed the allocated count even when the fence state changes between
the two passes. |
