| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: esp: fix bad handling of pages from page_pool
When the skb is reorganized during esp_output (!esp->inline), the pages
coming from the original skb fragments are supposed to be released back
to the system through put_page. But if the skb fragment pages are
originating from a page_pool, calling put_page on them will trigger a
page_pool leak which will eventually result in a crash.
This leak can be easily observed when using CONFIG_DEBUG_VM and doing
ipsec + gre (non offloaded) forwarding:
BUG: Bad page state in process ksoftirqd/16 pfn:1451b6
page:00000000de2b8d32 refcount:0 mapcount:0 mapping:0000000000000000 index:0x1451b6000 pfn:0x1451b6
flags: 0x200000000000000(node=0|zone=2)
page_type: 0xffffffff()
raw: 0200000000000000 dead000000000040 ffff88810d23c000 0000000000000000
raw: 00000001451b6000 0000000000000001 00000000ffffffff 0000000000000000
page dumped because: page_pool leak
Modules linked in: ip_gre gre mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core overlay zram zsmalloc fuse [last unloaded: mlx5_core]
CPU: 16 PID: 96 Comm: ksoftirqd/16 Not tainted 6.8.0-rc4+ #22
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x36/0x50
bad_page+0x70/0xf0
free_unref_page_prepare+0x27a/0x460
free_unref_page+0x38/0x120
esp_ssg_unref.isra.0+0x15f/0x200
esp_output_tail+0x66d/0x780
esp_xmit+0x2c5/0x360
validate_xmit_xfrm+0x313/0x370
? validate_xmit_skb+0x1d/0x330
validate_xmit_skb_list+0x4c/0x70
sch_direct_xmit+0x23e/0x350
__dev_queue_xmit+0x337/0xba0
? nf_hook_slow+0x3f/0xd0
ip_finish_output2+0x25e/0x580
iptunnel_xmit+0x19b/0x240
ip_tunnel_xmit+0x5fb/0xb60
ipgre_xmit+0x14d/0x280 [ip_gre]
dev_hard_start_xmit+0xc3/0x1c0
__dev_queue_xmit+0x208/0xba0
? nf_hook_slow+0x3f/0xd0
ip_finish_output2+0x1ca/0x580
ip_sublist_rcv_finish+0x32/0x40
ip_sublist_rcv+0x1b2/0x1f0
? ip_rcv_finish_core.constprop.0+0x460/0x460
ip_list_rcv+0x103/0x130
__netif_receive_skb_list_core+0x181/0x1e0
netif_receive_skb_list_internal+0x1b3/0x2c0
napi_gro_receive+0xc8/0x200
gro_cell_poll+0x52/0x90
__napi_poll+0x25/0x1a0
net_rx_action+0x28e/0x300
__do_softirq+0xc3/0x276
? sort_range+0x20/0x20
run_ksoftirqd+0x1e/0x30
smpboot_thread_fn+0xa6/0x130
kthread+0xcd/0x100
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x31/0x50
? kthread_complete_and_exit+0x20/0x20
ret_from_fork_asm+0x11/0x20
</TASK>
The suggested fix is to introduce a new wrapper (skb_page_unref) that
covers page refcounting for page_pool pages as well. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses
Since commit a4d5613c4dc6 ("arm: extend pfn_valid to take into account
freed memory map alignment") changes the semantics of pfn_valid() to check
presence of the memory map for a PFN. A valid page for an address which
is reserved but not mapped by the kernel[1], the system crashed during
some uio test with the following memory layout:
node 0: [mem 0x00000000c0a00000-0x00000000cc8fffff]
node 0: [mem 0x00000000d0000000-0x00000000da1fffff]
the uio layout is：0xc0900000, 0x100000
the crash backtrace like:
Unable to handle kernel paging request at virtual address bff00000
[...]
CPU: 1 PID: 465 Comm: startapp.bin Tainted: G O 5.10.0 #1
Hardware name: Generic DT based system
PC is at b15_flush_kern_dcache_area+0x24/0x3c
LR is at __sync_icache_dcache+0x6c/0x98
[...]
(b15_flush_kern_dcache_area) from (__sync_icache_dcache+0x6c/0x98)
(__sync_icache_dcache) from (set_pte_at+0x28/0x54)
(set_pte_at) from (remap_pfn_range+0x1a0/0x274)
(remap_pfn_range) from (uio_mmap+0x184/0x1b8 [uio])
(uio_mmap [uio]) from (__mmap_region+0x264/0x5f4)
(__mmap_region) from (__do_mmap_mm+0x3ec/0x440)
(__do_mmap_mm) from (do_mmap+0x50/0x58)
(do_mmap) from (vm_mmap_pgoff+0xfc/0x188)
(vm_mmap_pgoff) from (ksys_mmap_pgoff+0xac/0xc4)
(ksys_mmap_pgoff) from (ret_fast_syscall+0x0/0x5c)
Code: e0801001 e2423001 e1c00003 f57ff04f (ee070f3e)
---[ end trace 09cf0734c3805d52 ]---
Kernel panic - not syncing: Fatal exception
So check if PG_reserved was set to solve this issue.
[1]: https://lore.kernel.org/lkml/Zbtdue57RO0QScJM@linux.ibm.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix possible buffer overflow
struct hci_dev_info has a fixed size name[8] field so in the event that
hdev->name is bigger than that strcpy would attempt to write past its
size, so this fixes this problem by switching to use strscpy. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: af_bluetooth: Fix deadlock
Attemting to do sock_lock on .recvmsg may cause a deadlock as shown
bellow, so instead of using sock_sock this uses sk_receive_queue.lock
on bt_sock_ioctl to avoid the UAF:
INFO: task kworker/u9:1:121 blocked for more than 30 seconds.
Not tainted 6.7.6-lemon #183
Workqueue: hci0 hci_rx_work
Call Trace:
<TASK>
__schedule+0x37d/0xa00
schedule+0x32/0xe0
__lock_sock+0x68/0xa0
? __pfx_autoremove_wake_function+0x10/0x10
lock_sock_nested+0x43/0x50
l2cap_sock_recv_cb+0x21/0xa0
l2cap_recv_frame+0x55b/0x30a0
? psi_task_switch+0xeb/0x270
? finish_task_switch.isra.0+0x93/0x2a0
hci_rx_work+0x33a/0x3f0
process_one_work+0x13a/0x2f0
worker_thread+0x2f0/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe0/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix underflow in parse_server_interfaces()
In this loop, we step through the buffer and after each item we check
if the size_left is greater than the minimum size we need. However,
the problem is that "bytes_left" is type ssize_t while sizeof() is type
size_t. That means that because of type promotion, the comparison is
done as an unsigned and if we have negative bytes left the loop
continues instead of ending. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_mirred: use the backlog for mirred ingress
The test Davide added in commit ca22da2fbd69 ("act_mirred: use the backlog
for nested calls to mirred ingress") hangs our testing VMs every 10 or so
runs, with the familiar tcp_v4_rcv -> tcp_v4_rcv deadlock reported by
lockdep.
The problem as previously described by Davide (see Link) is that
if we reverse flow of traffic with the redirect (egress -> ingress)
we may reach the same socket which generated the packet. And we may
still be holding its socket lock. The common solution to such deadlocks
is to put the packet in the Rx backlog, rather than run the Rx path
inline. Do that for all egress -> ingress reversals, not just once
we started to nest mirred calls.
In the past there was a concern that the backlog indirection will
lead to loss of error reporting / less accurate stats. But the current
workaround does not seem to address the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: entry: fix ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
Currently the ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD workaround isn't
quite right, as it is supposed to be applied after the last explicit
memory access, but is immediately followed by an LDR.
The ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD workaround is used to
handle Cortex-A520 erratum 2966298 and Cortex-A510 erratum 3117295,
which are described in:
* https://developer.arm.com/documentation/SDEN2444153/0600/?lang=en
* https://developer.arm.com/documentation/SDEN1873361/1600/?lang=en
In both cases the workaround is described as:
| If pagetable isolation is disabled, the context switch logic in the
| kernel can be updated to execute the following sequence on affected
| cores before exiting to EL0, and after all explicit memory accesses:
|
| 1. A non-shareable TLBI to any context and/or address, including
| unused contexts or addresses, such as a `TLBI VALE1 Xzr`.
|
| 2. A DSB NSH to guarantee completion of the TLBI.
The important part being that the TLBI+DSB must be placed "after all
explicit memory accesses".
Unfortunately, as-implemented, the TLBI+DSB is immediately followed by
an LDR, as we have:
| alternative_if ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
| tlbi vale1, xzr
| dsb nsh
| alternative_else_nop_endif
| alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0
| ldr lr, [sp, #S_LR]
| add sp, sp, #PT_REGS_SIZE // restore sp
| eret
| alternative_else_nop_endif
|
| [ ... KPTI exception return path ... ]
This patch fixes this by reworking the logic to place the TLBI+DSB
immediately before the ERET, after all explicit memory accesses.
The ERET is currently in a separate alternative block, and alternatives
cannot be nested. To account for this, the alternative block for
ARM64_UNMAP_KERNEL_AT_EL0 is replaced with a single alternative branch
to skip the KPTI logic, with the new shape of the logic being:
| alternative_insn "b .L_skip_tramp_exit_\@", nop, ARM64_UNMAP_KERNEL_AT_EL0
| [ ... KPTI exception return path ... ]
| .L_skip_tramp_exit_\@:
|
| ldr lr, [sp, #S_LR]
| add sp, sp, #PT_REGS_SIZE // restore sp
|
| alternative_if ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
| tlbi vale1, xzr
| dsb nsh
| alternative_else_nop_endif
| eret
The new structure means that the workaround is only applied when KPTI is
not in use; this is fine as noted in the documented implications of the
erratum:
| Pagetable isolation between EL0 and higher level ELs prevents the
| issue from occurring.
... and as per the workaround description quoted above, the workaround
is only necessary "If pagetable isolation is disabled". |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: flower: Fix chain template offload
When a qdisc is deleted from a net device the stack instructs the
underlying driver to remove its flow offload callback from the
associated filter block using the 'FLOW_BLOCK_UNBIND' command. The stack
then continues to replay the removal of the filters in the block for
this driver by iterating over the chains in the block and invoking the
'reoffload' operation of the classifier being used. In turn, the
classifier in its 'reoffload' operation prepares and emits a
'FLOW_CLS_DESTROY' command for each filter.
However, the stack does not do the same for chain templates and the
underlying driver never receives a 'FLOW_CLS_TMPLT_DESTROY' command when
a qdisc is deleted. This results in a memory leak [1] which can be
reproduced using [2].
Fix by introducing a 'tmplt_reoffload' operation and have the stack
invoke it with the appropriate arguments as part of the replay.
Implement the operation in the sole classifier that supports chain
templates (flower) by emitting the 'FLOW_CLS_TMPLT_{CREATE,DESTROY}'
command based on whether a flow offload callback is being bound to a
filter block or being unbound from one.
As far as I can tell, the issue happens since cited commit which
reordered tcf_block_offload_unbind() before tcf_block_flush_all_chains()
in __tcf_block_put(). The order cannot be reversed as the filter block
is expected to be freed after flushing all the chains.
[1]
unreferenced object 0xffff888107e28800 (size 2048):
comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s)
hex dump (first 32 bytes):
b1 a6 7c 11 81 88 ff ff e0 5b b3 10 81 88 ff ff ..|......[......
01 00 00 00 00 00 00 00 e0 aa b0 84 ff ff ff ff ................
backtrace:
[<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320
[<ffffffff81ab374e>] __kmalloc+0x4e/0x90
[<ffffffff832aec6d>] mlxsw_sp_acl_ruleset_get+0x34d/0x7a0
[<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180
[<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280
[<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340
[<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0
[<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170
[<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0
[<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440
[<ffffffff83ac6270>] netlink_unicast+0x540/0x820
[<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0
[<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80
[<ffffffff8379d29a>] ___sys_sendmsg+0x13a/0x1e0
[<ffffffff8379d50c>] __sys_sendmsg+0x11c/0x1f0
[<ffffffff843b9ce0>] do_syscall_64+0x40/0xe0
unreferenced object 0xffff88816d2c0400 (size 1024):
comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s)
hex dump (first 32 bytes):
40 00 00 00 00 00 00 00 57 f6 38 be 00 00 00 00 @.......W.8.....
10 04 2c 6d 81 88 ff ff 10 04 2c 6d 81 88 ff ff ..,m......,m....
backtrace:
[<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320
[<ffffffff81ab36c1>] __kmalloc_node+0x51/0x90
[<ffffffff81a8ed96>] kvmalloc_node+0xa6/0x1f0
[<ffffffff82827d03>] bucket_table_alloc.isra.0+0x83/0x460
[<ffffffff82828d2b>] rhashtable_init+0x43b/0x7c0
[<ffffffff832aed48>] mlxsw_sp_acl_ruleset_get+0x428/0x7a0
[<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180
[<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280
[<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340
[<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0
[<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170
[<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0
[<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440
[<ffffffff83ac6270>] netlink_unicast+0x540/0x820
[<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0
[<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80
[2]
# tc qdisc add dev swp1 clsact
# tc chain add dev swp1 ingress proto ip chain 1 flower dst_ip 0.0.0.0/32
# tc qdisc del dev
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix 'panel_cntl' could be null in 'dcn21_set_backlight_level()'
'panel_cntl' structure used to control the display panel could be null,
dereferencing it could lead to a null pointer access.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn21/dcn21_hwseq.c:269 dcn21_set_backlight_level() error: we previously assumed 'panel_cntl' could be null (see line 250) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Add NULL test for 'timing generator' in 'dcn21_set_pipe()'
In "u32 otg_inst = pipe_ctx->stream_res.tg->inst;"
pipe_ctx->stream_res.tg could be NULL, it is relying on the caller to
ensure the tg is not NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject variable offset alu on PTR_TO_FLOW_KEYS
For PTR_TO_FLOW_KEYS, check_flow_keys_access() only uses fixed off
for validation. However, variable offset ptr alu is not prohibited
for this ptr kind. So the variable offset is not checked.
The following prog is accepted:
func#0 @0
0: R1=ctx() R10=fp0
0: (bf) r6 = r1 ; R1=ctx() R6_w=ctx()
1: (79) r7 = *(u64 *)(r6 +144) ; R6_w=ctx() R7_w=flow_keys()
2: (b7) r8 = 1024 ; R8_w=1024
3: (37) r8 /= 1 ; R8_w=scalar()
4: (57) r8 &= 1024 ; R8_w=scalar(smin=smin32=0,
smax=umax=smax32=umax32=1024,var_off=(0x0; 0x400))
5: (0f) r7 += r8
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r8 stack= before 4: (57) r8 &= 1024
mark_precise: frame0: regs=r8 stack= before 3: (37) r8 /= 1
mark_precise: frame0: regs=r8 stack= before 2: (b7) r8 = 1024
6: R7_w=flow_keys(smin=smin32=0,smax=umax=smax32=umax32=1024,var_off
=(0x0; 0x400)) R8_w=scalar(smin=smin32=0,smax=umax=smax32=umax32=1024,
var_off=(0x0; 0x400))
6: (79) r0 = *(u64 *)(r7 +0) ; R0_w=scalar()
7: (95) exit
This prog loads flow_keys to r7, and adds the variable offset r8
to r7, and finally causes out-of-bounds access:
BUG: unable to handle page fault for address: ffffc90014c80038
[...]
Call Trace:
<TASK>
bpf_dispatcher_nop_func include/linux/bpf.h:1231 [inline]
__bpf_prog_run include/linux/filter.h:651 [inline]
bpf_prog_run include/linux/filter.h:658 [inline]
bpf_prog_run_pin_on_cpu include/linux/filter.h:675 [inline]
bpf_flow_dissect+0x15f/0x350 net/core/flow_dissector.c:991
bpf_prog_test_run_flow_dissector+0x39d/0x620 net/bpf/test_run.c:1359
bpf_prog_test_run kernel/bpf/syscall.c:4107 [inline]
__sys_bpf+0xf8f/0x4560 kernel/bpf/syscall.c:5475
__do_sys_bpf kernel/bpf/syscall.c:5561 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5559 [inline]
__x64_sys_bpf+0x73/0xb0 kernel/bpf/syscall.c:5559
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fix this by rejecting ptr alu with variable offset on flow_keys.
Applying the patch rejects the program with "R7 pointer arithmetic
on flow_keys prohibited". |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/port: Fix delete_endpoint() vs parent unregistration race
The CXL subsystem, at cxl_mem ->probe() time, establishes a lineage of
ports (struct cxl_port objects) between an endpoint and the root of a
CXL topology. Each port including the endpoint port is attached to the
cxl_port driver.
Given that setup, it follows that when either any port in that lineage
goes through a cxl_port ->remove() event, or the memdev goes through a
cxl_mem ->remove() event. The hierarchy below the removed port, or the
entire hierarchy if the memdev is removed needs to come down.
The delete_endpoint() callback is careful to check whether it is being
called to tear down the hierarchy, or if it is only being called to
teardown the memdev because an ancestor port is going through
->remove().
That care needs to take the device_lock() of the endpoint's parent.
Which requires 2 bugs to be fixed:
1/ A reference on the parent is needed to prevent use-after-free
scenarios like this signature:
BUG: spinlock bad magic on CPU#0, kworker/u56:0/11
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20230524-3.fc38 05/24/2023
Workqueue: cxl_port detach_memdev [cxl_core]
RIP: 0010:spin_bug+0x65/0xa0
Call Trace:
do_raw_spin_lock+0x69/0xa0
__mutex_lock+0x695/0xb80
delete_endpoint+0xad/0x150 [cxl_core]
devres_release_all+0xb8/0x110
device_unbind_cleanup+0xe/0x70
device_release_driver_internal+0x1d2/0x210
detach_memdev+0x15/0x20 [cxl_core]
process_one_work+0x1e3/0x4c0
worker_thread+0x1dd/0x3d0
2/ In the case of RCH topologies, the parent device that needs to be
locked is not always @port->dev as returned by cxl_mem_find_port(), use
endpoint->dev.parent instead. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix use-after-free in smb2_query_info_compound()
The following UAF was triggered when running fstests generic/072 with
KASAN enabled against Windows Server 2022 and mount options
'multichannel,max_channels=2,vers=3.1.1,mfsymlinks,noperm'
BUG: KASAN: slab-use-after-free in smb2_query_info_compound+0x423/0x6d0 [cifs]
Read of size 8 at addr ffff888014941048 by task xfs_io/27534
CPU: 0 PID: 27534 Comm: xfs_io Not tainted 6.6.0-rc7 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
Call Trace:
dump_stack_lvl+0x4a/0x80
print_report+0xcf/0x650
? srso_alias_return_thunk+0x5/0x7f
? srso_alias_return_thunk+0x5/0x7f
? __phys_addr+0x46/0x90
kasan_report+0xda/0x110
? smb2_query_info_compound+0x423/0x6d0 [cifs]
? smb2_query_info_compound+0x423/0x6d0 [cifs]
smb2_query_info_compound+0x423/0x6d0 [cifs]
? __pfx_smb2_query_info_compound+0x10/0x10 [cifs]
? srso_alias_return_thunk+0x5/0x7f
? __stack_depot_save+0x39/0x480
? kasan_save_stack+0x33/0x60
? kasan_set_track+0x25/0x30
? ____kasan_slab_free+0x126/0x170
smb2_queryfs+0xc2/0x2c0 [cifs]
? __pfx_smb2_queryfs+0x10/0x10 [cifs]
? __pfx___lock_acquire+0x10/0x10
smb311_queryfs+0x210/0x220 [cifs]
? __pfx_smb311_queryfs+0x10/0x10 [cifs]
? srso_alias_return_thunk+0x5/0x7f
? __lock_acquire+0x480/0x26c0
? lock_release+0x1ed/0x640
? srso_alias_return_thunk+0x5/0x7f
? do_raw_spin_unlock+0x9b/0x100
cifs_statfs+0x18c/0x4b0 [cifs]
statfs_by_dentry+0x9b/0xf0
fd_statfs+0x4e/0xb0
__do_sys_fstatfs+0x7f/0xe0
? __pfx___do_sys_fstatfs+0x10/0x10
? srso_alias_return_thunk+0x5/0x7f
? lockdep_hardirqs_on_prepare+0x136/0x200
? srso_alias_return_thunk+0x5/0x7f
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Allocated by task 27534:
kasan_save_stack+0x33/0x60
kasan_set_track+0x25/0x30
__kasan_kmalloc+0x8f/0xa0
open_cached_dir+0x71b/0x1240 [cifs]
smb2_query_info_compound+0x5c3/0x6d0 [cifs]
smb2_queryfs+0xc2/0x2c0 [cifs]
smb311_queryfs+0x210/0x220 [cifs]
cifs_statfs+0x18c/0x4b0 [cifs]
statfs_by_dentry+0x9b/0xf0
fd_statfs+0x4e/0xb0
__do_sys_fstatfs+0x7f/0xe0
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Freed by task 27534:
kasan_save_stack+0x33/0x60
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2b/0x50
____kasan_slab_free+0x126/0x170
slab_free_freelist_hook+0xd0/0x1e0
__kmem_cache_free+0x9d/0x1b0
open_cached_dir+0xff5/0x1240 [cifs]
smb2_query_info_compound+0x5c3/0x6d0 [cifs]
smb2_queryfs+0xc2/0x2c0 [cifs]
This is a race between open_cached_dir() and cached_dir_lease_break()
where the cache entry for the open directory handle receives a lease
break while creating it. And before returning from open_cached_dir(),
we put the last reference of the new @cfid because of
!@cfid->has_lease.
Besides the UAF, while running xfstests a lot of missed lease breaks
have been noticed in tests that run several concurrent statfs(2) calls
on those cached fids
CIFS: VFS: \\w22-root1.gandalf.test No task to wake, unknown frame...
CIFS: VFS: \\w22-root1.gandalf.test Cmd: 18 Err: 0x0 Flags: 0x1...
CIFS: VFS: \\w22-root1.gandalf.test smb buf 00000000715bfe83 len 108
CIFS: VFS: Dump pending requests:
CIFS: VFS: \\w22-root1.gandalf.test No task to wake, unknown frame...
CIFS: VFS: \\w22-root1.gandalf.test Cmd: 18 Err: 0x0 Flags: 0x1...
CIFS: VFS: \\w22-root1.gandalf.test smb buf 000000005aa7316e len 108
...
To fix both, in open_cached_dir() ensure that @cfid->has_lease is set
right before sending out compounded request so that any potential
lease break will be get processed by demultiplex thread while we're
still caching @cfid. And, if open failed for some reason, re-check
@cfid->has_lease to decide whether or not put lease reference. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: fix a memleak in gss_import_v2_context
The ctx->mech_used.data allocated by kmemdup is not freed in neither
gss_import_v2_context nor it only caller gss_krb5_import_sec_context,
which frees ctx on error.
Thus, this patch reform the last call of gss_import_v2_context to the
gss_krb5_import_ctx_v2, preventing the memleak while keepping the return
formation. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: migrate: fix getting incorrect page mapping during page migration
When running stress-ng testing, we found below kernel crash after a few hours:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
pc : dentry_name+0xd8/0x224
lr : pointer+0x22c/0x370
sp : ffff800025f134c0
......
Call trace:
dentry_name+0xd8/0x224
pointer+0x22c/0x370
vsnprintf+0x1ec/0x730
vscnprintf+0x2c/0x60
vprintk_store+0x70/0x234
vprintk_emit+0xe0/0x24c
vprintk_default+0x3c/0x44
vprintk_func+0x84/0x2d0
printk+0x64/0x88
__dump_page+0x52c/0x530
dump_page+0x14/0x20
set_migratetype_isolate+0x110/0x224
start_isolate_page_range+0xc4/0x20c
offline_pages+0x124/0x474
memory_block_offline+0x44/0xf4
memory_subsys_offline+0x3c/0x70
device_offline+0xf0/0x120
......
After analyzing the vmcore, I found this issue is caused by page migration.
The scenario is that, one thread is doing page migration, and we will use the
target page's ->mapping field to save 'anon_vma' pointer between page unmap and
page move, and now the target page is locked and refcount is 1.
Currently, there is another stress-ng thread performing memory hotplug,
attempting to offline the target page that is being migrated. It discovers that
the refcount of this target page is 1, preventing the offline operation, thus
proceeding to dump the page. However, page_mapping() of the target page may
return an incorrect file mapping to crash the system in dump_mapping(), since
the target page->mapping only saves 'anon_vma' pointer without setting
PAGE_MAPPING_ANON flag.
There are seveval ways to fix this issue:
(1) Setting the PAGE_MAPPING_ANON flag for target page's ->mapping when saving
'anon_vma', but this can confuse PageAnon() for PFN walkers, since the target
page has not built mappings yet.
(2) Getting the page lock to call page_mapping() in __dump_page() to avoid crashing
the system, however, there are still some PFN walkers that call page_mapping()
without holding the page lock, such as compaction.
(3) Using target page->private field to save the 'anon_vma' pointer and 2 bits
page state, just as page->mapping records an anonymous page, which can remove
the page_mapping() impact for PFN walkers and also seems a simple way.
So I choose option 3 to fix this issue, and this can also fix other potential
issues for PFN walkers, such as compaction. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Do mark_chain_precision for ARG_CONST_ALLOC_SIZE_OR_ZERO
Precision markers need to be propagated whenever we have an ARG_CONST_*
style argument, as the verifier cannot consider imprecise scalars to be
equivalent for the purposes of states_equal check when such arguments
refine the return value (in this case, set mem_size for PTR_TO_MEM). The
resultant mem_size for the R0 is derived from the constant value, and if
the verifier incorrectly prunes states considering them equivalent where
such arguments exist (by seeing that both registers have reg->precise as
false in regsafe), we can end up with invalid programs passing the
verifier which can do access beyond what should have been the correct
mem_size in that explored state.
To show a concrete example of the problem:
0000000000000000 <prog>:
0: r2 = *(u32 *)(r1 + 80)
1: r1 = *(u32 *)(r1 + 76)
2: r3 = r1
3: r3 += 4
4: if r3 > r2 goto +18 <LBB5_5>
5: w2 = 0
6: *(u32 *)(r1 + 0) = r2
7: r1 = *(u32 *)(r1 + 0)
8: r2 = 1
9: if w1 == 0 goto +1 <LBB5_3>
10: r2 = -1
0000000000000058 <LBB5_3>:
11: r1 = 0 ll
13: r3 = 0
14: call bpf_ringbuf_reserve
15: if r0 == 0 goto +7 <LBB5_5>
16: r1 = r0
17: r1 += 16777215
18: w2 = 0
19: *(u8 *)(r1 + 0) = r2
20: r1 = r0
21: r2 = 0
22: call bpf_ringbuf_submit
00000000000000b8 <LBB5_5>:
23: w0 = 0
24: exit
For the first case, the single line execution's exploration will prune
the search at insn 14 for the branch insn 9's second leg as it will be
verified first using r2 = -1 (UINT_MAX), while as w1 at insn 9 will
always be 0 so at runtime we don't get error for being greater than
UINT_MAX/4 from bpf_ringbuf_reserve. The verifier during regsafe just
sees reg->precise as false for both r2 registers in both states, hence
considers them equal for purposes of states_equal.
If we propagated precise markers using the backtracking support, we
would use the precise marking to then ensure that old r2 (UINT_MAX) was
within the new r2 (1) and this would never be true, so the verification
would rightfully fail.
The end result is that the out of bounds access at instruction 19 would
be permitted without this fix.
Note that reg->precise is always set to true when user does not have
CAP_BPF (or when subprog count is greater than 1 (i.e. use of any static
or global functions)), hence this is only a problem when precision marks
need to be explicitly propagated (i.e. privileged users with CAP_BPF).
A simplified test case has been included in the next patch to prevent
future regressions. |
| In the Linux kernel, the following vulnerability has been resolved:
net: skbuff: preserve shared-frag marker during coalescing
skb_try_coalesce() can attach paged frags from @from to @to. If @from
has SKBFL_SHARED_FRAG set, the resulting @to skb can contain the same
externally-owned or page-cache-backed frags, but the shared-frag marker
is currently lost.
That breaks the invariant relied on by later in-place writers. In
particular, ESP input checks skb_has_shared_frag() before deciding
whether an uncloned nonlinear skb can skip skb_cow_data(). If TCP
receive coalescing has moved shared frags into an unmarked skb, ESP can
see skb_has_shared_frag() as false and decrypt in place over page-cache
backed frags.
Propagate SKBFL_SHARED_FRAG when skb_try_coalesce() transfers paged
frags. The tailroom copy path does not need the marker because it copies
bytes into @to's linear data rather than transferring frag descriptors. |
| A Null pointer dereference problem was found in ida_free in lib/idr.c in the Linux Kernel. This issue may allow an attacker using this library to cause a denial of service problem due to a missing check at a function return. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: imx6: Fix suspend/resume support on i.MX6QDL
The suspend/resume functionality is currently broken on the i.MX6QDL
platform, as documented in the NXP errata (ERR005723):
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch addresses the issue by sharing most of the suspend/resume
sequences used by other i.MX devices, while avoiding modifications to
critical registers that disrupt the PCIe functionality. It targets the
same problem as the following downstream commit:
https://github.com/nxp-imx/linux-imx/commit/4e92355e1f79d225ea842511fcfd42b343b32995
Unlike the downstream commit, this patch also resets the connected PCIe
device if possible. Without this reset, certain drivers, such as ath10k
or iwlwifi, will crash on resume. The device reset is also done by the
driver on other i.MX platforms, making this patch consistent with
existing practices.
Upon resuming, the kernel will hang and display an error. Here's an
example of the error encountered with the ath10k driver:
ath10k_pci 0000:01:00.0: Unable to change power state from D3hot to D0, device inaccessible
Unhandled fault: imprecise external abort (0x1406) at 0x0106f944
Without this patch, suspend/resume will fail on i.MX6QDL devices if a
PCIe device is connected.
[kwilczynski: commit log, added tag for stable releases] |
| In the Linux kernel, the following vulnerability has been resolved:
udmabuf: change folios array from kmalloc to kvmalloc
When PAGE_SIZE 4096, MAX_PAGE_ORDER 10, 64bit machine,
page_alloc only support 4MB.
If above this, trigger this warn and return NULL.
udmabuf can change size limit, if change it to 3072(3GB), and then alloc
3GB udmabuf, will fail create.
[ 4080.876581] ------------[ cut here ]------------
[ 4080.876843] WARNING: CPU: 3 PID: 2015 at mm/page_alloc.c:4556 __alloc_pages+0x2c8/0x350
[ 4080.878839] RIP: 0010:__alloc_pages+0x2c8/0x350
[ 4080.879470] Call Trace:
[ 4080.879473] <TASK>
[ 4080.879473] ? __alloc_pages+0x2c8/0x350
[ 4080.879475] ? __warn.cold+0x8e/0xe8
[ 4080.880647] ? __alloc_pages+0x2c8/0x350
[ 4080.880909] ? report_bug+0xff/0x140
[ 4080.881175] ? handle_bug+0x3c/0x80
[ 4080.881556] ? exc_invalid_op+0x17/0x70
[ 4080.881559] ? asm_exc_invalid_op+0x1a/0x20
[ 4080.882077] ? udmabuf_create+0x131/0x400
Because MAX_PAGE_ORDER, kmalloc can max alloc 4096 * (1 << 10), 4MB
memory, each array entry is pointer(8byte), so can save 524288 pages(2GB).
Further more, costly order(order 3) may not be guaranteed that it can be
applied for, due to fragmentation.
This patch change udmabuf array use kvmalloc_array, this can fallback
alloc into vmalloc, which can guarantee allocation for any size and does
not affect the performance of kmalloc allocations. |
