| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
qede: fix off-by-one in BD ring consumption on build_skb failure
qede_rx_build_skb() and qede_tpa_rx_build_skb() do not check for a
NULL return from qede_build_skb(). When it returns NULL under memory
pressure, the functions still consume a BD from the ring before
returning NULL. The callers then recycle additional BDs, resulting in
one extra BD being consumed (off-by-one). This desynchronizes the BD
ring, which can corrupt DMA page reference counts and lead to SLUB
freelist corruption.
Commit 4e910dbe3650 ("qede: confirm skb is allocated before using")
added a NULL check inside qede_build_skb() to prevent a NULL pointer
dereference, but did not address the missing NULL checks in the
callers, making this off-by-one reachable.
Fix this by adding NULL checks for the return value of
qede_build_skb() in both qede_rx_build_skb() and
qede_tpa_rx_build_skb(), returning NULL immediately before any BD ring
manipulation. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Check the interrupt is still ours before migrating it
vgic_prune_ap_list() drops both ap_list_lock and irq_lock while migrating
an interrupt to another vCPU. After reacquiring the locks it only checks
that the affinity is unchanged (target_vcpu == vgic_target_oracle(irq))
before moving the interrupt, which assumes that an interrupt whose affinity
is preserved is still queued on this vCPU's ap_list.
That assumption no longer holds if the interrupt is taken off the ap_list
while the locks are dropped. vgic_flush_pending_lpis() removes the
interrupt from the list and sets irq->vcpu to NULL, but leaves
enabled/pending/target_vcpu untouched. As the interrupt is still enabled
and pending, vgic_target_oracle() returns the same target_vcpu, so the
affinity check passes and list_del() is run a second time on an entry that
has already been removed.
Also check that the interrupt is still assigned to this vCPU
(irq->vcpu == vcpu) before moving it. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: KVM: Check irq validity in kvm_vcpu_ioctl_interrupt()
Function kvm_vcpu_ioctl_interrupt() can be called from userspace, here
add irq validility cheking in kvm_vcpu_ioctl_interrupt(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: ensure inner headers in ICMP errors are in headroom
Sashiko points out that after stripping the outer headers
with pskb_pull() we should ensure the inner IP headers
in ICMP errors from tunnels are present in the skb headroom
for functions like ipv4_update_pmtu(), icmp_send() and
IP_VS_DBG().
Also, add more checks for the length of the inner headers. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_lookup: fix catchall element handling with inverted lookups
nft_lookup_eval() decides whether a lookup matched (`found`) from the
direct set lookup and priv->invert before falling back to the
catchall element used by interval sets (e.g. nft_set_rbtree) for the
open-ended default range. Since `found` is never recomputed after
`ext` is replaced by the catchall lookup, inverted lookups
(NFT_LOOKUP_F_INV, "!= @set") can wrongly match or wrongly skip the
catchall element, producing the wrong verdict. Fold the catchall
lookup into `ext` before computing `found`, matching the order
already used by nft_objref_map_eval(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_connmark: reject invalid shift parameters
Revision 2 of the CONNMARK target accepts user-controlled shift
parameters and applies them to 32-bit mark values in
connmark_tg_shift().
A shift_bits value of 32 or more triggers an undefined-shift bug when
the rule is evaluated. Invalid shift_dir values are also accepted and
silently fall back to the left-shift path.
Reject invalid revision-2 shift parameters in connmark_tg_check() so
malformed rules fail at installation time, before they can reach the
packet path. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ip6tables: mark malformed IPv6 extension headers for hotdrop
The ah, hbh and rt matches check that the fixed extension header is
present, then use the header length field to derive the advertised
extension header length for matching.
For the ah match, add the missing advertised-length check. For hbh
and rt, update the existing advertised-length checks. In all three
cases, set hotdrop to true before returning false when the advertised
extension header length exceeds the available skb data.
Returning false treats the packet as a rule mismatch. Set hotdrop to
true and drop malformed packets so they cannot bypass rules intended
to drop packets with these IPv6 extension headers. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/pf: Don't attempt to process FAST_REQ or EVENT relays
Currently defined VF/PF relay actions use regular REQUEST messages
only and the PF shouldn't attempt to handle FAST_REQUEST nor EVENT
messages as this would result in breaking the VFPF ABI protocol
and also might trigger an assert on the PF side.
(cherry picked from commit 1714d360fc5ae2e0886a69e979095d9c7ff3568a) |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: guard io_size EOF trim against concurrent truncate underflow
iomap: fix zero padding data issue in concurrent append writes
changed ioend accounting so that io_size tracks only valid data
within EOF. This trims io_size when a writeback range extends
past end_pos:
ioend->io_size += map_len;
if (ioend->io_offset + ioend->io_size > end_pos)
ioend->io_size = end_pos - ioend->io_offset;
However, if end_pos ends up below ioend->io_offset, the subtraction
becomes negative and is stored in size_t io_size, causing an unsigned
wrap to a huge value. This can happen when writeback continues past
byte-level EOF up to a block-aligned range, or when a concurrent
truncate shrinks the file after end_pos was sampled in
iomap_writeback_handle_eof().
A wrapped io_size can mislead append detection and corrupt
completion-time size handling, since filesystem end_io paths consume
io_size for decisions such as on-disk EOF updates and unwritten/COW
completion ranges.
Fix this by clamping io_size to zero when EOF has moved to or before
the ioend start offset. This preserves the original intent of trimming
io_size to valid in-EOF data while avoiding the underflow. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sungem: fix probe error cleanup
gem_init_one() calls gem_remove_one() when register_netdev() fails.
gem_remove_one() unregisters and frees resources owned by the net_device,
including the DMA block, MMIO mapping, PCI regions, and the net_device
itself. gem_init_one() then falls through to its own cleanup labels and
frees the same resources again.
Keep the register_netdev() error path in gem_init_one(): clear drvdata so
PM/remove paths do not see a half-registered device, remove the NAPI
instance added during probe, and let the existing cleanup labels release
the resources once.
The issue was found by a local static-analysis checker for probe error
paths. The reported path was manually inspected before sending this fix.
Compile-tested with CONFIG_SUNGEM=y. Runtime testing was not performed
because no sungem hardware is available. |
| In the Linux kernel, the following vulnerability has been resolved:
seg6: validate SRH length before reading fixed fields
seg6_validate_srh() reads fixed SRH fields such as srh->type and
srh->hdrlen before checking that the supplied length covers the fixed
struct ipv6_sr_hdr fields.
The BPF SEG6 encap path reaches this with a BPF program-supplied pointer
and length: bpf_lwt_push_encap() and the SEG6 local BPF END_B6 and
END_B6_ENCAP actions call bpf_push_seg6_encap(), which forwards the
length to seg6_validate_srh() with no minimum-size guard. A 2-byte SEG6
encap header can therefore make the validator read srh->type at offset 2
beyond the caller-supplied buffer.
Reject lengths shorter than the fixed SRH at the top of
seg6_validate_srh(), before any field is read. This fixes the BPF helper
path and keeps the common validator robust. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: Validate iph->ihl in nf_flow_ip4_tunnel_proto()
Add sanity check for iph->ihl field in nf_flow_ip4_tunnel_proto() before
using it to compute the header size, avoiding out-of-bounds access with
malformed IP headers.
While at it, use iph->protocol instead of the hardcoded IPPROTO_IPIP
constant when setting ctx->tun.proto and reference ctx->tun.hdr_size
when updating ctx->offset. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: reject oversized nested action attrs
Open vSwitch stores generated flow actions as nlattrs, whose nla_len
field is u16. Commit a1e64addf3ff ("net: openvswitch: remove
misbehaving actions length check") allowed the total sw_flow_actions
stream to grow beyond 64 KiB, which is valid, but also removed the last
guard preventing a generated nested action attribute from exceeding
U16_MAX.
An oversized generated container can thus be closed with a truncated
nla_len. A later dump or teardown then walks a structurally different
stream than the one that was validated. In particular, an oversized
nested CLONE/CT action may cause subsequent bytes in the generated
stream to be interpreted as independent actions.
Keep the larger total-action-stream behavior, but make nested action
close reject generated containers that do not fit in nla_len, and return
the error through all callers. For recursive SAMPLE, CLONE, DEC_TTL, and
CHECK_PKT_LEN builders, trim resource-owning action-list tails in reverse
construction order before discarding failed wrappers, so resources copied
into the rejected tails are released before the wrappers are removed.
Most failed outer wrappers are discarded by truncating actions_len after
child resources have been released. CHECK_PKT_LEN also trims its parent
after branch resources are gone. SET/TUNNEL close failures unwind their
known tun_dst ownership directly, and SET_TO_MASKED has no external
ownership and truncates on close failure. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: qcom: reject stream disable with no active interface
handle_uaudio_stream_req() resolves an interface index with
info_idx_from_ifnum(), which returns -EINVAL when no interface matches.
The enable branch and the response: cleanup label both guard against a
negative index, but the disable branch does not: it forms
info = &uadev[pcm_card_num].info[info_idx] and dereferences it.
uadev[].info is a pointer allocated only when a stream is first enabled,
so a negative info_idx on the disable path is unsafe in two ways:
- If the card was never enabled, .info is NULL and &info[-EINVAL] is a
wild pointer; reading info->data_ep_pipe faults (kernel oops).
- If the card was enabled at least once (.info allocated) and the
disable names an interface that does not match, &info[-EINVAL] points
before the allocation; info->data_ep_pipe / info->sync_ep_pipe are an
out-of-bounds slab read and, when non-zero, an out-of-bounds 4-byte
write (both pipe fields are cleared to 0). That is memory corruption,
not just a NULL dereference.
The request is reachable from unprivileged local userspace over
AF_QIPCRTR. Reject a disable request with no resolved interface, matching
the guard the enable path already has. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: validate selector family and prefixlen during match
syzbot reported a shift-out-of-bounds in xfrm_selector_match()
due to AF_UNSPEC selector with large prefixlen (e.g. 128) matched
against IPv4 flow (when XFRM_STATE_AF_UNSPEC is set).
Fix this by:
- Rejecting mismatched families in xfrm_selector_match.
- Returning false in addr4_match if prefixlen > 32.
- Returning false in addr_match if prefixlen > 128 (prevents overflow). |
| In the Linux kernel, the following vulnerability has been resolved:
xprtrdma: Fix bcall rep leak and unbounded peek
rpcrdma_is_bcall() decodes a reply's first words to decide whether
the frame is a backchannel call. Two issues in that decode path
let a short or malformed reply leak the receive buffer and drain
the Receive queue.
First, the speculative peek
p = xdr_inline_decode(xdr, 0);
/* five p++ reads follow */
asks xdr_inline_decode() for zero bytes, which returns xdr->p
without consulting xdr->end. The five subsequent __be32 reads can
then walk up to 20 bytes past the wire payload into stale regbuf
contents and misclassify the reply as a backchannel call.
Second, after the post-peek
p = xdr_inline_decode(xdr, 3 * sizeof(*p));
if (unlikely(!p))
return true;
the short-header arm returns true without calling
rpcrdma_bc_receive_call(). The contract with the caller is that a
true return transfers ownership of rep to the backchannel path:
rpcrdma_reply_handler()
if (rpcrdma_is_bcall(r_xprt, rep))
return; /* bare return, skips out_post */
...
out_post:
rpcrdma_post_recvs(r_xprt, credits + ...);
Because rpcrdma_bc_receive_call() never ran, no one took rep, but
rpcrdma_reply_handler still bare-returns past rpcrdma_rep_put()
and rpcrdma_post_recvs(). The rep, with its persistently
DMA-mapped receive buffer, is orphaned on rb_all_reps and freed
only at transport teardown. This completion reposts nothing, so
its slot is reclaimed only when a later forward-channel reply
reaches out_post and rpcrdma_post_recvs() allocates a fresh rep to
backfill; absent that traffic the Receive queue drains and the
peer's Sends draw RNR NAKs.
Fix by consulting xdr->end after the zero-length peek so the five
__be32 reads cannot run unless 20 bytes of wire payload remain. A
byte-precise comparison against xdr->end is required because a
non-4-aligned receive rounds the stream's word count up past the
true payload. Also return false from the short-header arm so the
reply falls through the normal out_norqst cleanup chain
(rpcrdma_rep_put() plus rpcrdma_post_recvs()). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: xilinx-ams: fix out-of-bounds channel lookup in event handling
ams_event_to_channel() may return a pointer past the end of
dev->channels when no matching scan_index is found. This can lead
to invalid memory access in ams_handle_event().
Add a bounds check in ams_event_to_channel() and return NULL when
no channel is found. Also guard the caller to safely handle this
case. |
| In the Linux kernel, the following vulnerability has been resolved:
soundwire: fix bug in sdw_add_element_group_count found by syzkaller
The original implementation caused an out-of-bounds memory access
in the sdw_add_element_group_count for-loop when i == num.
for (i = 0; i <= num; i++) {
if (rate == group->rates[i] && lane == group->lanes[i])
...
To fix this error, the function now checks for existing rate/lane
entries in the group(a function parameter) using a for-loop before
adding them.
No functional changes apart from this fix. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: add bounds check to run_get_highest_vcn()
run_get_highest_vcn() parses a packed NTFS mapping-pairs buffer without
any length bound, relying solely on a 0x00 terminator to stop. A
crafted $LogFile UpdateMappingPairs record whose embedded attribute
contains mapping-pairs runs without a terminator causes the function to
read past the slab allocation, triggering a KASAN slab-out-of-bounds
read on mount.
The sibling function run_unpack() received an analogous bounds-check in
commit b62567bca474 ("ntfs3: add buffer boundary checks to run_unpack()"),
but run_get_highest_vcn() was missed.
Take a run_buf_size parameter and reject any run header whose payload
would extend past the buffer end, mirroring the pattern used by
run_unpack(). The caller in fslog.c passes the remaining attribute
bytes after the mapping-pairs offset.
KASAN report (on mainline v7.1 merge window HEAD):
BUG: KASAN: slab-out-of-bounds in run_get_highest_vcn+0x3c0/0x410
Read of size 1 at addr ffff88800e2d5400 by task mount/72
Call Trace:
run_get_highest_vcn+0x3c0/0x410
do_action.isra.0+0x3ba8/0x7b50
log_replay+0x9ddd/0x10200
ntfs_loadlog_and_replay+0x4ad/0x610
ntfs_fill_super+0x214a/0x4540 |
| In the Linux kernel, the following vulnerability has been resolved:
can: peak_usb: add bounds check for USB channel index
The channel control index ctrl_idx is derived from rx->len which comes
directly from a device USB payload. The mask 0x0f allows values 0-15, but
the array size of usb_if->dev[] is only 2. Values 2-15 cause heap
out-of-bounds read, eventually causing kernel panic in the IRQ context.
Add bounds checking for ctrl_idx before the array access in both
pcan_usb_pro_handle_canmsg() and pcan_usb_pro_handle_error(). |
