| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
lppaca_shared_proc() takes a pointer to the lppaca which is typically
accessed through get_lppaca(). With DEBUG_PREEMPT enabled, this leads
to checking if preemption is enabled, for example:
BUG: using smp_processor_id() in preemptible [00000000] code: grep/10693
caller is lparcfg_data+0x408/0x19a0
CPU: 4 PID: 10693 Comm: grep Not tainted 6.5.0-rc3 #2
Call Trace:
dump_stack_lvl+0x154/0x200 (unreliable)
check_preemption_disabled+0x214/0x220
lparcfg_data+0x408/0x19a0
...
This isn't actually a problem however, as it does not matter which
lppaca is accessed, the shared proc state will be the same.
vcpudispatch_stats_procfs_init() already works around this by disabling
preemption, but the lparcfg code does not, erroring any time
/proc/powerpc/lparcfg is accessed with DEBUG_PREEMPT enabled.
Instead of disabling preemption on the caller side, rework
lppaca_shared_proc() to not take a pointer and instead directly access
the lppaca, bypassing any potential preemption checks.
[mpe: Rework to avoid needing a definition in paca.h and lppaca.h] |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: fix memory leak in bnxt_nvm_test()
Free the kzalloc'ed buffer before returning in the success path. |
| In the Linux kernel, the following vulnerability has been resolved:
media: ipu3-imgu: Fix NULL pointer dereference in active selection access
What the IMGU driver did was that it first acquired the pointers to active
and try V4L2 subdev state, and only then figured out which one to use.
The problem with that approach and a later patch (see Fixes: tag) is that
as sd_state argument to v4l2_subdev_get_try_crop() et al is NULL, there is
now an attempt to dereference that.
Fix this.
Also rewrap lines a little. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
syzkaller reported use-after-free with the stack trace like below [1]:
[ 38.960489][ C3] ==================================================================
[ 38.963216][ C3] BUG: KASAN: use-after-free in ar5523_cmd_tx_cb+0x220/0x240
[ 38.964950][ C3] Read of size 8 at addr ffff888048e03450 by task swapper/3/0
[ 38.966363][ C3]
[ 38.967053][ C3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.0.0-09039-ga6afa4199d3d-dirty #18
[ 38.968464][ C3] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
[ 38.969959][ C3] Call Trace:
[ 38.970841][ C3] <IRQ>
[ 38.971663][ C3] dump_stack_lvl+0xfc/0x174
[ 38.972620][ C3] print_report.cold+0x2c3/0x752
[ 38.973626][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.974644][ C3] kasan_report+0xb1/0x1d0
[ 38.975720][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.976831][ C3] ar5523_cmd_tx_cb+0x220/0x240
[ 38.978412][ C3] __usb_hcd_giveback_urb+0x353/0x5b0
[ 38.979755][ C3] usb_hcd_giveback_urb+0x385/0x430
[ 38.981266][ C3] dummy_timer+0x140c/0x34e0
[ 38.982925][ C3] ? notifier_call_chain+0xb5/0x1e0
[ 38.984761][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.986242][ C3] ? lock_release+0x51c/0x790
[ 38.987323][ C3] ? _raw_read_unlock_irqrestore+0x37/0x70
[ 38.988483][ C3] ? __wake_up_common_lock+0xde/0x130
[ 38.989621][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 38.990777][ C3] ? lock_acquire+0x472/0x550
[ 38.991919][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.993138][ C3] ? lock_acquire+0x472/0x550
[ 38.994890][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.996266][ C3] ? do_raw_spin_unlock+0x16f/0x230
[ 38.997670][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.999116][ C3] call_timer_fn+0x1a0/0x6a0
[ 39.000668][ C3] ? add_timer_on+0x4a0/0x4a0
[ 39.002137][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 39.003809][ C3] ? __next_timer_interrupt+0x226/0x2a0
[ 39.005509][ C3] __run_timers.part.0+0x69a/0xac0
[ 39.007025][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 39.008716][ C3] ? call_timer_fn+0x6a0/0x6a0
[ 39.010254][ C3] ? cpuacct_percpu_seq_show+0x10/0x10
[ 39.011795][ C3] ? kvm_sched_clock_read+0x14/0x40
[ 39.013277][ C3] ? sched_clock_cpu+0x69/0x2b0
[ 39.014724][ C3] run_timer_softirq+0xb6/0x1d0
[ 39.016196][ C3] __do_softirq+0x1d2/0x9be
[ 39.017616][ C3] __irq_exit_rcu+0xeb/0x190
[ 39.019004][ C3] irq_exit_rcu+0x5/0x20
[ 39.020361][ C3] sysvec_apic_timer_interrupt+0x8f/0xb0
[ 39.021965][ C3] </IRQ>
[ 39.023237][ C3] <TASK>
In ar5523_probe(), ar5523_host_available() calls ar5523_cmd() as below
(there are other functions which finally call ar5523_cmd()):
ar5523_probe()
-> ar5523_host_available()
-> ar5523_cmd_read()
-> ar5523_cmd()
If ar5523_cmd() timed out, then ar5523_host_available() failed and
ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb()
might touch the freed structure.
This patch fixes this issue by canceling in-flight tx cmd if submitted
urb timed out. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: stop mdx_raid1 thread when raid1 array run failed
fail run raid1 array when we assemble array with the inactive disk only,
but the mdx_raid1 thread were not stop, Even if the associated resources
have been released. it will caused a NULL dereference when we do poweroff.
This causes the following Oops:
[ 287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070
[ 287.594762] #PF: supervisor read access in kernel mode
[ 287.599912] #PF: error_code(0x0000) - not-present page
[ 287.605061] PGD 0 P4D 0
[ 287.607612] Oops: 0000 [#1] SMP NOPTI
[ 287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G U 5.10.146 #0
[ 287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022
[ 287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod]
[ 287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ......
[ 287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202
[ 287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000
[ 287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800
[ 287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff
[ 287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800
[ 287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500
[ 287.692052] FS: 0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000
[ 287.700149] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0
[ 287.713033] Call Trace:
[ 287.715498] raid1d+0x6c/0xbbb [raid1]
[ 287.719256] ? __schedule+0x1ff/0x760
[ 287.722930] ? schedule+0x3b/0xb0
[ 287.726260] ? schedule_timeout+0x1ed/0x290
[ 287.730456] ? __switch_to+0x11f/0x400
[ 287.734219] md_thread+0xe9/0x140 [md_mod]
[ 287.738328] ? md_thread+0xe9/0x140 [md_mod]
[ 287.742601] ? wait_woken+0x80/0x80
[ 287.746097] ? md_register_thread+0xe0/0xe0 [md_mod]
[ 287.751064] kthread+0x11a/0x140
[ 287.754300] ? kthread_park+0x90/0x90
[ 287.757974] ret_from_fork+0x1f/0x30
In fact, when raid1 array run fail, we need to do
md_unregister_thread() before raid1_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
clk: visconti: Fix memory leak in visconti_register_pll()
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it. |
| In the Linux kernel, the following vulnerability has been resolved:
HSI: ssi_protocol: fix potential resource leak in ssip_pn_open()
ssip_pn_open() claims the HSI client's port with hsi_claim_port(). When
hsi_register_port_event() gets some error and returns a negetive value,
the HSI client's port should be released with hsi_release_port().
Fix it by calling hsi_release_port() when hsi_register_port_event() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-crypto: fix memory leak in virtio_crypto_alg_skcipher_close_session()
'vc_ctrl_req' is alloced in virtio_crypto_alg_skcipher_close_session(),
and should be freed in the invalid ctrl_status->status error handling
case. Otherwise there is a memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
net/ieee802154: don't warn zero-sized raw_sendmsg()
syzbot is hitting skb_assert_len() warning at __dev_queue_xmit() [1],
for PF_IEEE802154 socket's zero-sized raw_sendmsg() request is hitting
__dev_queue_xmit() with skb->len == 0.
Since PF_IEEE802154 socket's zero-sized raw_sendmsg() request was
able to return 0, don't call __dev_queue_xmit() if packet length is 0.
----------
#include <sys/socket.h>
#include <netinet/in.h>
int main(int argc, char *argv[])
{
struct sockaddr_in addr = { .sin_family = AF_INET, .sin_addr.s_addr = htonl(INADDR_LOOPBACK) };
struct iovec iov = { };
struct msghdr hdr = { .msg_name = &addr, .msg_namelen = sizeof(addr), .msg_iov = &iov, .msg_iovlen = 1 };
sendmsg(socket(PF_IEEE802154, SOCK_RAW, 0), &hdr, 0);
return 0;
}
----------
Note that this might be a sign that commit fd1894224407c484 ("bpf: Don't
redirect packets with invalid pkt_len") should be reverted, for
skb->len == 0 was acceptable for at least PF_IEEE802154 socket. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: set tx_tstamps when creating new Tx rings via ethtool
When the user changes the number of queues via ethtool, the driver
allocates new rings. This allocation did not initialize tx_tstamps. This
results in the tx_tstamps field being zero (due to kcalloc allocation), and
would result in a NULL pointer dereference when attempting a transmit
timestamp on the new ring. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: Fix use-after-free during usb config switch
In the process of switching USB config from rndis to other config,
if the hardware does not support the ->pullup callback, or the
hardware encounters a low probability fault, both of them may cause
the ->pullup callback to fail, which will then cause a system panic
(use after free).
The gadget drivers sometimes need to be unloaded regardless of the
hardware's behavior.
Analysis as follows:
=======================================================================
(1) write /config/usb_gadget/g1/UDC "none"
gether_disconnect+0x2c/0x1f8
rndis_disable+0x4c/0x74
composite_disconnect+0x74/0xb0
configfs_composite_disconnect+0x60/0x7c
usb_gadget_disconnect+0x70/0x124
usb_gadget_unregister_driver+0xc8/0x1d8
gadget_dev_desc_UDC_store+0xec/0x1e4
(2) rm /config/usb_gadget/g1/configs/b.1/f1
rndis_deregister+0x28/0x54
rndis_free+0x44/0x7c
usb_put_function+0x14/0x1c
config_usb_cfg_unlink+0xc4/0xe0
configfs_unlink+0x124/0x1c8
vfs_unlink+0x114/0x1dc
(3) rmdir /config/usb_gadget/g1/functions/rndis.gs4
panic+0x1fc/0x3d0
do_page_fault+0xa8/0x46c
do_mem_abort+0x3c/0xac
el1_sync_handler+0x40/0x78
0xffffff801138f880
rndis_close+0x28/0x34
eth_stop+0x74/0x110
dev_close_many+0x48/0x194
rollback_registered_many+0x118/0x814
unregister_netdev+0x20/0x30
gether_cleanup+0x1c/0x38
rndis_attr_release+0xc/0x14
kref_put+0x74/0xb8
configfs_rmdir+0x314/0x374
If gadget->ops->pullup() return an error, function rndis_close() will be
called, then it will causes a use-after-free problem.
======================================================================= |
| In the Linux kernel, the following vulnerability has been resolved:
soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
There are two refcount leak bugs in qcom_smsm_probe():
(1) The 'local_node' is escaped out from for_each_child_of_node() as
the break of iteration, we should call of_node_put() for it in error
path or when it is not used anymore.
(2) The 'node' is escaped out from for_each_available_child_of_node()
as the 'goto', we should call of_node_put() for it in goto target. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: xgmiitorgmii: Fix refcount leak in xgmiitorgmii_probe
of_phy_find_device() return device node with refcount incremented.
Call put_device() to relese it when not needed anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
media: usb: siano: Fix use after free bugs caused by do_submit_urb
There are UAF bugs caused by do_submit_urb(). One of the KASan reports
is shown below:
[ 36.403605] BUG: KASAN: use-after-free in worker_thread+0x4a2/0x890
[ 36.406105] Read of size 8 at addr ffff8880059600e8 by task kworker/0:2/49
[ 36.408316]
[ 36.408867] CPU: 0 PID: 49 Comm: kworker/0:2 Not tainted 6.2.0-rc3-15798-g5a41237ad1d4-dir8
[ 36.411696] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g15584
[ 36.416157] Workqueue: 0x0 (events)
[ 36.417654] Call Trace:
[ 36.418546] <TASK>
[ 36.419320] dump_stack_lvl+0x96/0xd0
[ 36.420522] print_address_description+0x75/0x350
[ 36.421992] print_report+0x11b/0x250
[ 36.423174] ? _raw_spin_lock_irqsave+0x87/0xd0
[ 36.424806] ? __virt_addr_valid+0xcf/0x170
[ 36.426069] ? worker_thread+0x4a2/0x890
[ 36.427355] kasan_report+0x131/0x160
[ 36.428556] ? worker_thread+0x4a2/0x890
[ 36.430053] worker_thread+0x4a2/0x890
[ 36.431297] ? worker_clr_flags+0x90/0x90
[ 36.432479] kthread+0x166/0x190
[ 36.433493] ? kthread_blkcg+0x50/0x50
[ 36.434669] ret_from_fork+0x22/0x30
[ 36.435923] </TASK>
[ 36.436684]
[ 36.437215] Allocated by task 24:
[ 36.438289] kasan_set_track+0x50/0x80
[ 36.439436] __kasan_kmalloc+0x89/0xa0
[ 36.440566] smsusb_probe+0x374/0xc90
[ 36.441920] usb_probe_interface+0x2d1/0x4c0
[ 36.443253] really_probe+0x1d5/0x580
[ 36.444539] __driver_probe_device+0xe3/0x130
[ 36.446085] driver_probe_device+0x49/0x220
[ 36.447423] __device_attach_driver+0x19e/0x1b0
[ 36.448931] bus_for_each_drv+0xcb/0x110
[ 36.450217] __device_attach+0x132/0x1f0
[ 36.451470] bus_probe_device+0x59/0xf0
[ 36.452563] device_add+0x4ec/0x7b0
[ 36.453830] usb_set_configuration+0xc63/0xe10
[ 36.455230] usb_generic_driver_probe+0x3b/0x80
[ 36.456166] printk: console [ttyGS0] disabled
[ 36.456569] usb_probe_device+0x90/0x110
[ 36.459523] really_probe+0x1d5/0x580
[ 36.461027] __driver_probe_device+0xe3/0x130
[ 36.462465] driver_probe_device+0x49/0x220
[ 36.463847] __device_attach_driver+0x19e/0x1b0
[ 36.465229] bus_for_each_drv+0xcb/0x110
[ 36.466466] __device_attach+0x132/0x1f0
[ 36.467799] bus_probe_device+0x59/0xf0
[ 36.469010] device_add+0x4ec/0x7b0
[ 36.470125] usb_new_device+0x863/0xa00
[ 36.471374] hub_event+0x18c7/0x2220
[ 36.472746] process_one_work+0x34c/0x5b0
[ 36.474041] worker_thread+0x4b7/0x890
[ 36.475216] kthread+0x166/0x190
[ 36.476267] ret_from_fork+0x22/0x30
[ 36.477447]
[ 36.478160] Freed by task 24:
[ 36.479239] kasan_set_track+0x50/0x80
[ 36.480512] kasan_save_free_info+0x2b/0x40
[ 36.481808] ____kasan_slab_free+0x122/0x1a0
[ 36.483173] __kmem_cache_free+0xc4/0x200
[ 36.484563] smsusb_term_device+0xcd/0xf0
[ 36.485896] smsusb_probe+0xc85/0xc90
[ 36.486976] usb_probe_interface+0x2d1/0x4c0
[ 36.488303] really_probe+0x1d5/0x580
[ 36.489498] __driver_probe_device+0xe3/0x130
[ 36.491140] driver_probe_device+0x49/0x220
[ 36.492475] __device_attach_driver+0x19e/0x1b0
[ 36.493988] bus_for_each_drv+0xcb/0x110
[ 36.495171] __device_attach+0x132/0x1f0
[ 36.496617] bus_probe_device+0x59/0xf0
[ 36.497875] device_add+0x4ec/0x7b0
[ 36.498972] usb_set_configuration+0xc63/0xe10
[ 36.500264] usb_generic_driver_probe+0x3b/0x80
[ 36.501740] usb_probe_device+0x90/0x110
[ 36.503084] really_probe+0x1d5/0x580
[ 36.504241] __driver_probe_device+0xe3/0x130
[ 36.505548] driver_probe_device+0x49/0x220
[ 36.506766] __device_attach_driver+0x19e/0x1b0
[ 36.508368] bus_for_each_drv+0xcb/0x110
[ 36.509646] __device_attach+0x132/0x1f0
[ 36.510911] bus_probe_device+0x59/0xf0
[ 36.512103] device_add+0x4ec/0x7b0
[ 36.513215] usb_new_device+0x863/0xa00
[ 36.514736] hub_event+0x18c7/0x2220
[ 36.516130] process_one_work+
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix invalid address access when enabling SCAN log level
The variable i is changed when setting random MAC address and causes
invalid address access when printing the value of pi->reqs[i]->reqid.
We replace reqs index with ri to fix the issue.
[ 136.726473] Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000000
[ 136.737365] Mem abort info:
[ 136.740172] ESR = 0x96000004
[ 136.743359] Exception class = DABT (current EL), IL = 32 bits
[ 136.749294] SET = 0, FnV = 0
[ 136.752481] EA = 0, S1PTW = 0
[ 136.755635] Data abort info:
[ 136.758514] ISV = 0, ISS = 0x00000004
[ 136.762487] CM = 0, WnR = 0
[ 136.765522] user pgtable: 4k pages, 48-bit VAs, pgdp = 000000005c4e2577
[ 136.772265] [0000000000000000] pgd=0000000000000000
[ 136.777160] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 136.782732] Modules linked in: brcmfmac(O) brcmutil(O) cfg80211(O) compat(O)
[ 136.789788] Process wificond (pid: 3175, stack limit = 0x00000000053048fb)
[ 136.796664] CPU: 3 PID: 3175 Comm: wificond Tainted: G O 4.19.42-00001-g531a5f5 #1
[ 136.805532] Hardware name: Freescale i.MX8MQ EVK (DT)
[ 136.810584] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 136.815429] pc : brcmf_pno_config_sched_scans+0x6cc/0xa80 [brcmfmac]
[ 136.821811] lr : brcmf_pno_config_sched_scans+0x67c/0xa80 [brcmfmac]
[ 136.828162] sp : ffff00000e9a3880
[ 136.831475] x29: ffff00000e9a3890 x28: ffff800020543400
[ 136.836786] x27: ffff8000b1008880 x26: ffff0000012bf6a0
[ 136.842098] x25: ffff80002054345c x24: ffff800088d22400
[ 136.847409] x23: ffff0000012bf638 x22: ffff0000012bf6d8
[ 136.852721] x21: ffff8000aced8fc0 x20: ffff8000ac164400
[ 136.858032] x19: ffff00000e9a3946 x18: 0000000000000000
[ 136.863343] x17: 0000000000000000 x16: 0000000000000000
[ 136.868655] x15: ffff0000093f3b37 x14: 0000000000000050
[ 136.873966] x13: 0000000000003135 x12: 0000000000000000
[ 136.879277] x11: 0000000000000000 x10: ffff000009a61888
[ 136.884589] x9 : 000000000000000f x8 : 0000000000000008
[ 136.889900] x7 : 303a32303d726464 x6 : ffff00000a1f957d
[ 136.895211] x5 : 0000000000000000 x4 : ffff00000e9a3942
[ 136.900523] x3 : 0000000000000000 x2 : ffff0000012cead8
[ 136.905834] x1 : ffff0000012bf6d8 x0 : 0000000000000000
[ 136.911146] Call trace:
[ 136.913623] brcmf_pno_config_sched_scans+0x6cc/0xa80 [brcmfmac]
[ 136.919658] brcmf_pno_start_sched_scan+0xa4/0x118 [brcmfmac]
[ 136.925430] brcmf_cfg80211_sched_scan_start+0x80/0xe0 [brcmfmac]
[ 136.931636] nl80211_start_sched_scan+0x140/0x308 [cfg80211]
[ 136.937298] genl_rcv_msg+0x358/0x3f4
[ 136.940960] netlink_rcv_skb+0xb4/0x118
[ 136.944795] genl_rcv+0x34/0x48
[ 136.947935] netlink_unicast+0x264/0x300
[ 136.951856] netlink_sendmsg+0x2e4/0x33c
[ 136.955781] __sys_sendto+0x120/0x19c |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: Fix leak of dev tracker
At the stage of direction checks, the netdev reference tracker is
already initialized, but released with wrong *_put() call. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: zynq-ipi: fix error handling while device_register() fails
If device_register() fails, it has two issues:
1. The name allocated by dev_set_name() is leaked.
2. The parent of device is not NULL, device_unregister() is called
in zynqmp_ipi_free_mboxes(), it will lead a kernel crash because
of removing not added device.
Call put_device() to give up the reference, so the name is freed in
kobject_cleanup(). Add device registered check in zynqmp_ipi_free_mboxes()
to avoid null-ptr-deref. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srpt: Add a check for valid 'mad_agent' pointer
When unregistering MAD agent, srpt module has a non-null check
for 'mad_agent' pointer before invoking ib_unregister_mad_agent().
This check can pass if 'mad_agent' variable holds an error value.
The 'mad_agent' can have an error value for a short window when
srpt_add_one() and srpt_remove_one() is executed simultaneously.
In srpt module, added a valid pointer check for 'sport->mad_agent'
before unregistering MAD agent.
This issue can hit when RoCE driver unregisters ib_device
Stack Trace:
------------
BUG: kernel NULL pointer dereference, address: 000000000000004d
PGD 145003067 P4D 145003067 PUD 2324fe067 PMD 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 10 PID: 4459 Comm: kworker/u80:0 Kdump: loaded Tainted: P
Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.5.4 01/13/2020
Workqueue: bnxt_re bnxt_re_task [bnxt_re]
RIP: 0010:_raw_spin_lock_irqsave+0x19/0x40
Call Trace:
ib_unregister_mad_agent+0x46/0x2f0 [ib_core]
IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
? __schedule+0x20b/0x560
srpt_unregister_mad_agent+0x93/0xd0 [ib_srpt]
srpt_remove_one+0x20/0x150 [ib_srpt]
remove_client_context+0x88/0xd0 [ib_core]
bond0: (slave p2p1): link status definitely up, 100000 Mbps full duplex
disable_device+0x8a/0x160 [ib_core]
bond0: active interface up!
? kernfs_name_hash+0x12/0x80
(NULL device *): Bonding Info Received: rdev: 000000006c0b8247
__ib_unregister_device+0x42/0xb0 [ib_core]
(NULL device *): Master: mode: 4 num_slaves:2
ib_unregister_device+0x22/0x30 [ib_core]
(NULL device *): Slave: id: 105069936 name:p2p1 link:0 state:0
bnxt_re_stopqps_and_ib_uninit+0x83/0x90 [bnxt_re]
bnxt_re_alloc_lag+0x12e/0x4e0 [bnxt_re] |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-frontends: fix leak of memory fw |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Fix memory leak in ath11k_peer_rx_frag_setup
crypto_alloc_shash() allocates resources, which should be released by
crypto_free_shash(). When ath11k_peer_find() fails, there has memory
leak. Add missing crypto_free_shash() to fix this. |
