| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Fix CMD_SYNC use-after-free on teardown
arm_smmu_impl_remove() is registered as a devres action in
arm_smmu_impl_probe(), before arm_smmu_init_queues() allocates
smmu->cmdq.q.base. On a devres unwind, whether a failed probe or an
unbind, the queue is freed first and arm_smmu_impl_remove() then runs
tegra241_cmdqv_remove_vintf(), whose VINTF deinit issues a CMD_SYNC on
the freed memory.
Observed during testing with a QEMU hack that makes the VCMDQ fail to
enable, so the impl reset fails and probe aborts into the devres unwind:
platform NVDA200C:00: tegra241_cmdqv: VINTF0: VCMDQ0/LVCMDQ0: failed to enable, STATUS=0x00000000
platform NVDA200C:00: tegra241_cmdqv: VINTF0: VCMDQ0/LVCMDQ0: GERRORN=0x0, GERROR=0x4, CONS=0x0
platform NVDA200C:00: tegra241_cmdqv: VINTF0: VCMDQ0/LVCMDQ0: uncleared error detected, resetting
arm-smmu-v3 arm-smmu-v3.0.auto: failed to reset impl
arm-smmu-v3 arm-smmu-v3.0.auto: probe with driver arm-smmu-v3 failed with error -110
Unable to handle kernel paging request at virtual address ffff8000891e0098
...
Internal error: Oops: 0000000096000047 [#1] SMP
...
Call trace:
arm_smmu_cmdq_issue_cmdlist+0x320/0x6fc (P)
tegra241_vcmdq_hw_deinit+0x98/0x168
tegra241_vintf_hw_deinit+0x5c/0x1b0
tegra241_cmdqv_remove_vintf+0x34/0xec
tegra241_cmdqv_remove+0x40/0x9c
arm_smmu_impl_remove+0x20/0x30
devm_action_release+0x14/0x20
devres_release_all+0xa8/0x110
device_unbind_cleanup+0x18/0x84
really_probe+0x1f0/0x29c
Drop the VINTF deinit from tegra241_cmdqv_remove_vintf() so the unwind no
longer touches the freed queue. Quiesce the VINTFs earlier instead. Add a
device_disable() impl op and run it from arm_smmu_disable_action() while
the CMDQ is still up. That handles a live unbind. A failed reset is already
handled because tegra241_vintf_hw_init() deinits the VINTF on its own error
path. tegra241_cmdqv_remove_vintf() is also used by the iommufd viommu
destroy path, so quiesce there too. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: nintendo: register input device after capabilities are set
input_register_device() exposes the device to userspace immediately.
In joycon_input_create() it was called before joycon_config_rumble()
configures the FF_RUMBLE capability and the memless force-feedback
device, so a concurrent EVIOCSFF could dereference a NULL dev->ff.
Registering early also means the initial udev event lacks button and
axis information, which can make input managers ignore the device.
Move input_register_device() to the end of joycon_input_create(), after
all capabilities, the IMU input device and the force-feedback callbacks
have been configured. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: asus: fix missing hid_is_usb() check
to_usb_interface() can only be used on a hid_device whose parent is really
USB; uhid can create devices that identify as being on BUS_USB, but don't
actually have a USB parent.
Fix the use of to_usb_interface() without a hid_is_usb() check.
I have verified that it is currently possible to trigger a kernel splat due
to this bug in an ASAN build, and that this commit fixes the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
futex/pi: Reject cross-mm private futex owners
A private futex key borrows the waiter's mm without taking an mm_users
reference. Nevertheless, attach_to_pi_owner() currently accepts an owner
from a different address space and copies the private key into the owner's
PI state.
When that owner exits, exit_pi_state_list() uses the saved key to find the
hash bucket and acquires a reference to the waiter's private hash. If the
last user of the waiter's mm exits concurrently, futex_hash_free() frees
the hash while the owner still uses its bucket and reference.
Prevent this by validating in attach_to_pi_owner() that, for private
futexes, the owner mm and waiter mm are the same. Perform the check with
the owner's pi_lock held and after validating owner::futex::state to
serialize against a concurrent PI-state exit cleanup.
[ tglx: Amended comment ] |
| In the Linux kernel, the following vulnerability has been resolved:
HID: magicmouse: do not keep a stale msc->input if no input is claimed
magicmouse_input_mapping() caches the first hid_input's input_dev in
msc->input while the report descriptor is parsed, and the rest of the
driver treats a non-NULL msc->input as proof that an input device was
registered.
That does not hold on the hid-input error path. If hidinput_connect()
fails -- for instance because input_register_device() returns an error --
it unwinds through hidinput_disconnect(), which frees every input_dev it
created, including the one cached in msc->input.
The failure does not abort the probe. hid_connect() only skips the claim:
if ((connect_mask & HID_CONNECT_HIDINPUT) && !hidinput_connect(hdev,
connect_mask & HID_CONNECT_HIDINPUT_FORCE))
hdev->claimed |= HID_CLAIMED_INPUT;
and the "device has no listeners" bailout below it does not fire for this
driver, which sets ->raw_event; on the USB Magic Mouse 2 / Magic Trackpad
2 paths hidraw and hiddev are claimed as well. hid_hw_start() therefore
returns 0 and magicmouse_probe() continues with msc->input pointing at
freed memory. Being non-NULL, it passes the "input not registered" check
in probe and the NULL checks in ->raw_event and ->event, so the next
input report dereferences freed memory.
Clear msc->input when the HID core did not claim an input device, so the
existing NULL checks cover this case as well. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: magicmouse: prevent unbounded recursion in magicmouse_raw_event()
magicmouse_raw_event() handles DOUBLE_REPORT_ID (0xf7) packets, which pack
two touch reports into one, by splitting the packet and calling itself on
each half. The only guard against runaway recursion is a "size < 1" check,
which stops zero-sized calls but does not bound the recursion depth.
A malicious HID device that matches this driver can send a report starting
with DOUBLE_REPORT_ID and filled with the sequence [0xf7, 0x00]. Each level
consumes two bytes and recurses on the remainder, so an incoming report of
up to HID_MAX_BUFFER_SIZE (16 KiB) drives roughly 8000 nested calls. That
easily exhausts the 16 KiB kernel stack, leading to a stack overflow: a
panic with CONFIG_VMAP_STACK, or memory corruption without it.
A double report only ever wraps two normal reports; it is never
legitimately nested. Refuse to re-enter the DOUBLE_REPORT_ID case from a
recursive call so the recursion depth is bounded to two, while all valid
packets keep being parsed exactly as before. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: pm: fix memory leak from alloc-during-teardown race
mptcp_pm_destroy() empties msk->pm.anno_list and
msk->pm.userspace_pm_local_addr_list under msk->pm.lock during socket
teardown, dropping the lock between the two.
A concurrent userspace PM genl ANNOUNCE on the same msk holds a sock
reference via mptcp_token_get_sock() and, in
mptcp_pm_nl_announce_doit(), calls
mptcp_userspace_pm_append_new_local_addr() and
mptcp_pm_announced_alloc(). Both take msk->pm.lock briefly to add to
their respective lists. Because the genl handler holds a sock reference,
mptcp_pm_destroy() may run on the same msk via mptcp_disconnect(), which
invokes mptcp_destroy_common() without dropping the sock refcount,
before the handler completes.
If the lock acquisitions interleave such that mptcp_pm_destroy() empties
a list first, the later alloc adds its entry to a list head that nothing
else iterates for this msk, and the entry leaks. kmemleak reports both
mptcp_pm_add_addr objects (from mptcp_pm_announced_alloc()) and
mptcp_pm_addr_entry objects (from
mptcp_userspace_pm_append_new_local_addr()) under sustained concurrent
ANNOUNCE + close load against the userspace PM.
Add an MPTCP_PM_DESTROYING bit in msk->pm.status, set by
mptcp_pm_destroy() under pm.lock before the lists are emptied and
checked under pm.lock by the alloc paths. Either the alloc takes pm.lock
first, in which case its entry is on the list when mptcp_pm_destroy()
frees it; or mptcp_pm_destroy() takes pm.lock first, in which case the
later alloc observes the bit and refuses.
Found by an MPTCP protocol-flow harness extending BRF (arXiv:2305.08782). |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: fix invalid free in LS IOD error path
nvmet_fc_alloc_ls_iodlist() advances iod while initializing the LS IOD
array. If an rqstbuf allocation or response buffer DMA mapping fails,
the unwind loop decrements iod past the start of the array. The final
kfree(iod) therefore frees an address before the allocated object.
This can be reproduced with nvme-fcloop and failslab by setting
fail-nth to 6 before creating a target port. KASAN reports:
BUG: KASAN: invalid-free in nvmet_fc_register_targetport
Free of addr ffff88816cf8ff48 by task nvmet_fail_nth/9552
Free the original allocation base stored in tgtport->iod instead. With
this fix applied, the same sysfs write with fail-nth=6 returns -ENOMEM
without any KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix use-after-free in ip6_finish_output2()
ip6_finish_output2() caches a pointer to the IPv6 destination
address (daddr) before invoking lwtunnel_xmit(). The LWT-BPF
transmit path or other encapsulation operations within
lwtunnel_xmit() can reallocate the skb head, freeing the memory
that daddr points to. When lwtunnel_xmit() returns
LWTUNNEL_XMIT_CONTINUE, the function continues to use the stale
daddr pointer to compute the nexthop and to look up or create the
neighbour entry. This results in a use-after-free read, which can
leak sensitive kernel data, pollute the neighbour table with
arbitrary values, misdirect traffic, or crash the system.
Fix this by re-fetching the IPv6 header and the destination
address pointer after lwtunnel_xmit() returns
LWTUNNEL_XMIT_CONTINUE, ensuring that the subsequent nexthop
computation and neighbour lookup operate on valid memory. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: nci: add data_len bound checks to activation parameter extractors
nci_extract_activation_params_iso_dep() and
nci_extract_activation_params_nfc_dep() read an inner length byte from
the NCI RF_INTF_ACTIVATED_NTF payload and use it to memcpy() into fixed
kernel buffers, but neither function receives the caller-validated
activation_params_len. A crafted NCI notification with
activation_params_len=1 and an inner length byte of up to 20 (NFC-A) or
50 (NFC-B) causes memcpy() to read that many bytes past the one valid
byte in the activation params region -- a slab out-of-bounds read of
kernel memory adjacent to the NCI skb.
The sibling nci_extract_rf_params_*() family was given equivalent
protection by commit 571dcbeb8e63 ("net: nfc: nci: Fix parameter
validation for packet data"), but the two activation parameter
extractors were not updated at that time.
Add a data_len parameter to both functions, guard against an empty
region before consuming the inner length byte, decrement the remaining
count after consuming it, and clamp the copy length to what is actually
available. Update both call sites to pass ntf.activation_params_len,
which is already validated against the skb at ntf.c:801. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: pn533: purge fragmented skbs during cleanup
pn53x_common_clean() purges resp_q before freeing the common PN533 state,
but it leaves fragment_skb untouched. The fragmentation helpers queue
transmit fragments there while sending large initiator or target-mode
frames, and those skbs remain owned by the driver until they are sent or
discarded.
If the device is removed while fragments are still queued, the common
cleanup path frees the PN533 state without releasing the queued fragment
skbs, leaking them.
Purge fragment_skb during cleanup alongside resp_q. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: fix OOB read and u8 offset wrap in TLV parsers
nfc_llcp_parse_gb_tlv() and nfc_llcp_parse_connection_tlv() contain
three related bugs in their TLV parsing loops:
1. 'offset' is declared u8 but tlv_array_len is u16. When TLV data
advances offset past 255 it silently wraps to zero, causing
infinite loops or double-processing of buffer data.
2. Before reading tlv[0] (type) and tlv[1] (length) there is no
check that offset+2 <= tlv_array_len. A truncated TLV causes
an OOB read of one byte past the buffer end.
3. After reading the length field, the value bytes are accessed
without checking offset+2+length <= tlv_array_len. A crafted
length=0xFF on a short buffer causes up to 255 bytes of OOB
read past the buffer end.
Both functions are reachable without authentication via
nfc_llcp_set_remote_gb() which feeds remote LLCP general bytes
directly into nfc_llcp_parse_gb_tlv() with no additional
validation.
Fix all three issues by widening offset from u8 to u16 and adding
bounds checks for both the TLV header and value field before each
access. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: digital: clamp SENSF_RES length to the destination buffer
digital_in_recv_sensf_res() memcpy()s resp->len bytes from a remote
NFC-F device response into the NFC_SENSF_RES_MAXSIZE-byte target.sensf_res
field without an upper-bound check. A nearby malicious NFC-F device can
send an oversized SENSF_RES response to overflow the stack-local struct
nfc_target.
Clamp resp->len to NFC_SENSF_RES_MAXSIZE before the copy.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: validate attr entry pointer before field access
xfs_attr3_leaf_verify_entry() accesses lentry/rentry fields (namelen,
valuelen) before checking if the entry pointer itself is within bounds.
If nameidx is crafted to point near the end of the buffer, these field
accesses can read out-of-bounds before the bounds check at
name_end > buf_end is performed.
Add explicit bounds checks for entry pointers before accessing their
fields. Use offsetof() to check that the start of the flexible array
member (nameval/name) is within bounds, which ensures all preceding
fields are safe to access. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: don't enable DAX on new encrypted files
Currently, when a new encrypted regular file is created, the call to
ext4_set_inode_flags(inode, init=true) in __ext4_new_inode() is made
before EXT4_INODE_ENCRYPT is set. As a result, it can set S_DAX if the
filesystem is mounted with "-o dax=always".
EXT4_INODE_ENCRYPT then actually gets set a bit later in
__ext4_new_inode(), when it calls fscrypt_set_context() which calls
ext4_set_context(). ext4_set_context() sets EXT4_INODE_ENCRYPT and
calls ext4_set_inode_flags(inode, init=false) to set S_ENCRYPTED too.
This was intended to clear S_DAX as well. However, this was broken by
commit 043546e46dc7 ("fs/ext4: Only change S_DAX on inode load"). This
causes data written to the file to bypass encryption, also causing
xfstests failures such as generic/548 (when "-o dax=always" is used).
Fix this by simplifying the flow by making __ext4_new_inode() set
EXT4_INODE_ENCRYPT earlier. This makes it take effect in
ext4_set_inode_flags(inode, init=true), making S_DAX never be set.
Similarly, make EXT4_STATE_MAY_INLINE_DATA never be set in the first
place on new encrypted inodes. Then it doesn't need to be cleared.
As a result of these simplifications, ext4_set_context() no longer needs
to change inode flags or state when 'handle != NULL'. Remove that too. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_aml: validate firmware segment lengths
aml_download_firmware() reads two lengths from the firmware header and
uses them to build pointers before checking that the header and segment
data are present. A truncated or inconsistent firmware image can make
the driver read past firmware->data while constructing TCI commands.
Reject images shorter than the header and ensure that the ICCM and DCCM
ranges fit within the loaded firmware before downloading either segment. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: uclogic: fix use-after-free of inrange_timer on remove
uclogic_remove() cancels the pen in-range timer and then stops the
device:
timer_delete_sync(&drvdata->inrange_timer);
hid_hw_stop(hdev);
timer_delete_sync() only guarantees the timer is idle at that instant.
uclogic_raw_event_pen() keeps delivering pen reports until hid_hw_stop()
stops the transport several lines later, and every report with
pen->inrange == UCLOGIC_PARAMS_PEN_INRANGE_NONE re-arms the timer:
mod_timer(&drvdata->inrange_timer, jiffies + msecs_to_jiffies(100));
A report landing between the timer_delete_sync() call and the transport
teardown in hid_hw_stop() re-arms inrange_timer after it was cancelled.
uclogic_remove() then returns and the devm drvdata is freed, while
hid_hw_stop() has already freed the input device drvdata->pen_input
points at, so when the timer fires ~100 ms later
uclogic_inrange_timeout() dereferences freed memory -- a use-after-free
in timer-softirq context.
Swapping the two calls is not a fix: stopping the device first frees
drvdata->pen_input via hidinput_disconnect() while the timer may still
be pending, so a timer already armed before removal fires on the freed
input device in the window before timer_delete_sync() runs.
Use timer_shutdown_sync() before hid_hw_stop() instead. It cancels the
timer, waits for a running callback while pen_input is still valid, and
prevents any further re-arming -- a later mod_timer() from an in-flight
report is silently ignored -- so the timer is provably dead before
hid_hw_stop() frees the inputs. This is the ordering the timer core
documents for this "timer re-armed from another path" teardown case. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: sensor: custom: Fix use-after-free in enable_sensor
enable_sensor_store() can call set_power_report_state(), which
dereferences sensor_inst->power_state and sensor_inst->report_state.
These pointers refer to entries in sensor_inst->fields.
Create the field attributes before exposing the enable_sensor sysfs
attribute, so enable_sensor cannot be accessed before the state it
depends on has been initialized.
On remove, delete enable_sensor before freeing the field attributes,
so a concurrent sysfs write cannot dereference freed memory through
power_state or report_state. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/cmd: fix iovec leak when the async cmd is not recycled
An io_async_cmd carries an iovec array in ->vec.iovec, allocated when the
vec has to grow and kept across recycling through ctx->cmd_cache. On two
paths nothing frees it and io_clean_op()'s kfree(req->async_data) drops
the io_async_cmd without it.
io_req_uring_cleanup() clears the async data flags only when
io_alloc_cache_put() succeeds, and the cache holds IO_ALLOC_CACHE_MAX ==
128 entries, so once it is full the put fails and the vec is left behind.
An NVMe passthrough workload gets there without doing anything unusual:
nvme_uring_cmd_io() returns -EIOCBQUEUED, so the io_async_cmd stays
attached for the lifetime of the command and the live object count tracks
the queue depth. Above 128 the puts start failing.
->cleanup is the last chance to free an inherited vec, since
io_req_uring_cleanup() returns early for an io-wq issued command and is
not called at all for one completed without ever being issued. But
io_clean_op() calls ->cleanup only if REQ_F_NEED_CLEANUP is set, and for
uring_cmd that happens only where the vec has to grow, so a command
reusing a large enough cached vec never sets it. io_rw_alloc_async() and
io_msg_alloc_async() flag an inherited vec for exactly this reason;
io_uring_cmd_prep() does not.
Flag an inherited vec in io_uring_cmd_prep(), and free the vec when the
cache put fails, as io_req_rw_cleanup() does.
The leak is invisible under KASAN, where io_alloc_cache_vec_kasan() frees
the vec unconditionally. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: dummy: Check card index validity at probe
snd_dummy_probe() blindly trusts that the given devptr->id value is
within the proper card index range. It's OK for the devices the
driver itself creates at the module probe time, but if the device is
bound manually via sysfs interface, this could be -1 as "none", and
this leads to OOB access for index[] and other parameters.
Add a sanity check for the card index and warn/correct it if it's a
value out of the range. |
