| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Cap MSIX used to online CPUs + 1
The irdma driver can use a maximum number of msix vectors equal
to num_online_cpus() + 1 and the kernel warning stack below is shown
if that number is exceeded.
The kernel throws a warning as the driver tries to update the affinity
hint with a CPU mask greater than the max CPU IDs. Fix this by capping
the MSIX vectors to num_online_cpus() + 1.
WARNING: CPU: 7 PID: 23655 at include/linux/cpumask.h:106 irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
RIP: 0010:irdma_cfg_ceq_vector+0x34c/0x3f0 [irdma]
Call Trace:
irdma_rt_init_hw+0xa62/0x1290 [irdma]
? irdma_alloc_local_mac_entry+0x1a0/0x1a0 [irdma]
? __is_kernel_percpu_address+0x63/0x310
? rcu_read_lock_held_common+0xe/0xb0
? irdma_lan_unregister_qset+0x280/0x280 [irdma]
? irdma_request_reset+0x80/0x80 [irdma]
? ice_get_qos_params+0x84/0x390 [ice]
irdma_probe+0xa40/0xfc0 [irdma]
? rcu_read_lock_bh_held+0xd0/0xd0
? irdma_remove+0x140/0x140 [irdma]
? rcu_read_lock_sched_held+0x62/0xe0
? down_write+0x187/0x3d0
? auxiliary_match_id+0xf0/0x1a0
? irdma_remove+0x140/0x140 [irdma]
auxiliary_bus_probe+0xa6/0x100
__driver_probe_device+0x4a4/0xd50
? __device_attach_driver+0x2c0/0x2c0
driver_probe_device+0x4a/0x110
__driver_attach+0x1aa/0x350
bus_for_each_dev+0x11d/0x1b0
? subsys_dev_iter_init+0xe0/0xe0
bus_add_driver+0x3b1/0x610
driver_register+0x18e/0x410
? 0xffffffffc0b88000
irdma_init_module+0x50/0xaa [irdma]
do_one_initcall+0x103/0x5f0
? perf_trace_initcall_level+0x420/0x420
? do_init_module+0x4e/0x700
? __kasan_kmalloc+0x7d/0xa0
? kmem_cache_alloc_trace+0x188/0x2b0
? kasan_unpoison+0x21/0x50
do_init_module+0x1d1/0x700
load_module+0x3867/0x5260
? layout_and_allocate+0x3990/0x3990
? rcu_read_lock_held_common+0xe/0xb0
? rcu_read_lock_sched_held+0x62/0xe0
? rcu_read_lock_bh_held+0xd0/0xd0
? __vmalloc_node_range+0x46b/0x890
? lock_release+0x5c8/0xba0
? alloc_vm_area+0x120/0x120
? selinux_kernel_module_from_file+0x2a5/0x300
? __inode_security_revalidate+0xf0/0xf0
? __do_sys_init_module+0x1db/0x260
__do_sys_init_module+0x1db/0x260
? load_module+0x5260/0x5260
? do_syscall_64+0x22/0x450
do_syscall_64+0xa5/0x450
entry_SYSCALL_64_after_hwframe+0x66/0xdb |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/vaddr: do not repeat pte_offset_map_lock() until success
DAMON's virtual address space operation set implementation (vaddr) calls
pte_offset_map_lock() inside the page table walk callback function. This
is for reading and writing page table accessed bits. If
pte_offset_map_lock() fails, it retries by returning the page table walk
callback function with ACTION_AGAIN.
pte_offset_map_lock() can continuously fail if the target is a pmd
migration entry, though. Hence it could cause an infinite page table walk
if the migration cannot be done until the page table walk is finished.
This indeed caused a soft lockup when CPU hotplugging and DAMON were
running in parallel.
Avoid the infinite loop by simply not retrying the page table walk. DAMON
is promising only a best-effort accuracy, so missing access to such pages
is no problem. |
| In the Linux kernel, the following vulnerability has been resolved:
fscrypt: fix left shift underflow when inode->i_blkbits > PAGE_SHIFT
When simulating an nvme device on qemu with both logical_block_size and
physical_block_size set to 8 KiB, an error trace appears during
partition table reading at boot time. The issue is caused by
inode->i_blkbits being larger than PAGE_SHIFT, which leads to a left
shift of -1 and triggering a UBSAN warning.
[ 2.697306] ------------[ cut here ]------------
[ 2.697309] UBSAN: shift-out-of-bounds in fs/crypto/inline_crypt.c:336:37
[ 2.697311] shift exponent -1 is negative
[ 2.697315] CPU: 3 UID: 0 PID: 274 Comm: (udev-worker) Not tainted 6.18.0-rc2+ #34 PREEMPT(voluntary)
[ 2.697317] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 2.697320] Call Trace:
[ 2.697324] <TASK>
[ 2.697325] dump_stack_lvl+0x76/0xa0
[ 2.697340] dump_stack+0x10/0x20
[ 2.697342] __ubsan_handle_shift_out_of_bounds+0x1e3/0x390
[ 2.697351] bh_get_inode_and_lblk_num.cold+0x12/0x94
[ 2.697359] fscrypt_set_bio_crypt_ctx_bh+0x44/0x90
[ 2.697365] submit_bh_wbc+0xb6/0x190
[ 2.697370] block_read_full_folio+0x194/0x270
[ 2.697371] ? __pfx_blkdev_get_block+0x10/0x10
[ 2.697375] ? __pfx_blkdev_read_folio+0x10/0x10
[ 2.697377] blkdev_read_folio+0x18/0x30
[ 2.697379] filemap_read_folio+0x40/0xe0
[ 2.697382] filemap_get_pages+0x5ef/0x7a0
[ 2.697385] ? mmap_region+0x63/0xd0
[ 2.697389] filemap_read+0x11d/0x520
[ 2.697392] blkdev_read_iter+0x7c/0x180
[ 2.697393] vfs_read+0x261/0x390
[ 2.697397] ksys_read+0x71/0xf0
[ 2.697398] __x64_sys_read+0x19/0x30
[ 2.697399] x64_sys_call+0x1e88/0x26a0
[ 2.697405] do_syscall_64+0x80/0x670
[ 2.697410] ? __x64_sys_newfstat+0x15/0x20
[ 2.697414] ? x64_sys_call+0x204a/0x26a0
[ 2.697415] ? do_syscall_64+0xb8/0x670
[ 2.697417] ? irqentry_exit_to_user_mode+0x2e/0x2a0
[ 2.697420] ? irqentry_exit+0x43/0x50
[ 2.697421] ? exc_page_fault+0x90/0x1b0
[ 2.697422] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 2.697425] RIP: 0033:0x75054cba4a06
[ 2.697426] Code: 5d e8 41 8b 93 08 03 00 00 59 5e 48 83 f8 fc 75 19 83 e2 39 83 fa 08 75 11 e8 26 ff ff ff 66 0f 1f 44 00 00 48 8b 45 10 0f 05 <48> 8b 5d f8 c9 c3 0f 1f 40 00 f3 0f 1e fa 55 48 89 e5 48 83 ec 08
[ 2.697427] RSP: 002b:00007fff973723a0 EFLAGS: 00000202 ORIG_RAX: 0000000000000000
[ 2.697430] RAX: ffffffffffffffda RBX: 00005ea9a2c02760 RCX: 000075054cba4a06
[ 2.697432] RDX: 0000000000002000 RSI: 000075054c190000 RDI: 000000000000001b
[ 2.697433] RBP: 00007fff973723c0 R08: 0000000000000000 R09: 0000000000000000
[ 2.697434] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
[ 2.697434] R13: 00005ea9a2c027c0 R14: 00005ea9a2be5608 R15: 00005ea9a2be55f0
[ 2.697436] </TASK>
[ 2.697436] ---[ end trace ]---
This situation can happen for block devices because when
CONFIG_TRANSPARENT_HUGEPAGE is enabled, the maximum logical_block_size
is 64 KiB. set_init_blocksize() then sets the block device
inode->i_blkbits to 13, which is within this limit.
File I/O does not trigger this problem because for filesystems that do
not support the FS_LBS feature, sb_set_blocksize() prevents
sb->s_blocksize_bits from being larger than PAGE_SHIFT. During inode
allocation, alloc_inode()->inode_init_always() assigns inode->i_blkbits
from sb->s_blocksize_bits. Currently, only xfs_fs_type has the FS_LBS
flag, and since xfs I/O paths do not reach submit_bh_wbc(), it does not
hit the left-shift underflow issue.
[EB: use folio_pos() and consolidate the two shifts by i_blkbits] |
| In the Linux kernel, the following vulnerability has been resolved:
9p/trans_fd: p9_fd_request: kick rx thread if EPOLLIN
p9_read_work() doesn't set Rworksched and doesn't do schedule_work(m->rq)
if list_empty(&m->req_list).
However, if the pipe is full, we need to read more data and this used to
work prior to commit aaec5a95d59615 ("pipe_read: don't wake up the writer
if the pipe is still full").
p9_read_work() does p9_fd_read() -> ... -> anon_pipe_read() which (before
the commit above) triggered the unnecessary wakeup. This wakeup calls
p9_pollwake() which kicks p9_poll_workfn() -> p9_poll_mux(), p9_poll_mux()
will notice EPOLLIN and schedule_work(&m->rq).
This no longer happens after the optimization above, change p9_fd_request()
to use p9_poll_mux() instead of only checking for EPOLLOUT. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: udc: fix use-after-free in usb_gadget_state_work
A race condition during gadget teardown can lead to a use-after-free
in usb_gadget_state_work(), as reported by KASAN:
BUG: KASAN: invalid-access in sysfs_notify+0x2c/0xd0
Workqueue: events usb_gadget_state_work
The fundamental race occurs because a concurrent event (e.g., an
interrupt) can call usb_gadget_set_state() and schedule gadget->work
at any time during the cleanup process in usb_del_gadget().
Commit 399a45e5237c ("usb: gadget: core: flush gadget workqueue after
device removal") attempted to fix this by moving flush_work() to after
device_del(). However, this does not fully solve the race, as a new
work item can still be scheduled *after* flush_work() completes but
before the gadget's memory is freed, leading to the same use-after-free.
This patch fixes the race condition robustly by introducing a 'teardown'
flag and a 'state_lock' spinlock to the usb_gadget struct. The flag is
set during cleanup in usb_del_gadget() *before* calling flush_work() to
prevent any new work from being scheduled once cleanup has commenced.
The scheduling site, usb_gadget_set_state(), now checks this flag under
the lock before queueing the work, thus safely closing the race window. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memfd: fix information leak in hugetlb folios
When allocating hugetlb folios for memfd, three initialization steps are
missing:
1. Folios are not zeroed, leading to kernel memory disclosure to userspace
2. Folios are not marked uptodate before adding to page cache
3. hugetlb_fault_mutex is not taken before hugetlb_add_to_page_cache()
The memfd allocation path bypasses the normal page fault handler
(hugetlb_no_page) which would handle all of these initialization steps.
This is problematic especially for udmabuf use cases where folios are
pinned and directly accessed by userspace via DMA.
Fix by matching the initialization pattern used in hugetlb_no_page():
- Zero the folio using folio_zero_user() which is optimized for huge pages
- Mark it uptodate with folio_mark_uptodate()
- Take hugetlb_fault_mutex before adding to page cache to prevent races
The folio_zero_user() change also fixes a potential security issue where
uninitialized kernel memory could be disclosed to userspace through read()
or mmap() operations on the memfd. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: Fix device use-after-free on unbind
A recent change fixed device reference leaks when looking up drm
platform device driver data during bind() but failed to remove a partial
fix which had been added by commit 80805b62ea5b ("drm/mediatek: Fix
kobject put for component sub-drivers").
This results in a reference imbalance on component bind() failures and
on unbind() which could lead to a user-after-free.
Make sure to only drop the references after retrieving the driver data
by effectively reverting the previous partial fix.
Note that holding a reference to a device does not prevent its driver
data from going away so there is no point in keeping the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Check the TLS certificate fields in nfs_match_client()
If the TLS security policy is of type RPC_XPRTSEC_TLS_X509, then the
cert_serial and privkey_serial fields need to match as well since they
define the client's identity, as presented to the server. |
| In the Linux kernel, the following vulnerability has been resolved:
bcache: fixup btree_cache_wait list damage
We get a kernel crash about "list_add corruption. next->prev should be
prev (ffff9c801bc01210), but was ffff9c77b688237c.
(next=ffffae586d8afe68)."
crash> struct list_head 0xffff9c801bc01210
struct list_head {
next = 0xffffae586d8afe68,
prev = 0xffffae586d8afe68
}
crash> struct list_head 0xffff9c77b688237c
struct list_head {
next = 0x0,
prev = 0x0
}
crash> struct list_head 0xffffae586d8afe68
struct list_head struct: invalid kernel virtual address: ffffae586d8afe68 type: "gdb_readmem_callback"
Cannot access memory at address 0xffffae586d8afe68
[230469.019492] Call Trace:
[230469.032041] prepare_to_wait+0x8a/0xb0
[230469.044363] ? bch_btree_keys_free+0x6c/0xc0 [escache]
[230469.056533] mca_cannibalize_lock+0x72/0x90 [escache]
[230469.068788] mca_alloc+0x2ae/0x450 [escache]
[230469.080790] bch_btree_node_get+0x136/0x2d0 [escache]
[230469.092681] bch_btree_check_thread+0x1e1/0x260 [escache]
[230469.104382] ? finish_wait+0x80/0x80
[230469.115884] ? bch_btree_check_recurse+0x1a0/0x1a0 [escache]
[230469.127259] kthread+0x112/0x130
[230469.138448] ? kthread_flush_work_fn+0x10/0x10
[230469.149477] ret_from_fork+0x35/0x40
bch_btree_check_thread() and bch_dirty_init_thread() may call
mca_cannibalize() to cannibalize other cached btree nodes. Only one thread
can do it at a time, so the op of other threads will be added to the
btree_cache_wait list.
We must call finish_wait() to remove op from btree_cache_wait before free
it's memory address. Otherwise, the list will be damaged. Also should call
bch_cannibalize_unlock() to release the btree_cache_alloc_lock and wake_up
other waiters. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/firmware: Add missing kfree() of nvkm_falcon_fw::boot
nvkm_falcon_fw::boot is allocated, but no one frees it. This causes a
kmemleak warning.
Make sure this data is deallocated. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: ti: netcp: Standardize knav_dma_open_channel to return NULL on error
Make knav_dma_open_channel consistently return NULL on error instead
of ERR_PTR. Currently the header include/linux/soc/ti/knav_dma.h
returns NULL when the driver is disabled, but the driver
implementation does not even return NULL or ERR_PTR on failure,
causing inconsistency in the users. This results in a crash in
netcp_free_navigator_resources as followed (trimmed):
Unhandled fault: alignment exception (0x221) at 0xfffffff2
[fffffff2] *pgd=80000800207003, *pmd=82ffda003, *pte=00000000
Internal error: : 221 [#1] SMP ARM
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.17.0-rc7 #1 NONE
Hardware name: Keystone
PC is at knav_dma_close_channel+0x30/0x19c
LR is at netcp_free_navigator_resources+0x2c/0x28c
[... TRIM...]
Call trace:
knav_dma_close_channel from netcp_free_navigator_resources+0x2c/0x28c
netcp_free_navigator_resources from netcp_ndo_open+0x430/0x46c
netcp_ndo_open from __dev_open+0x114/0x29c
__dev_open from __dev_change_flags+0x190/0x208
__dev_change_flags from netif_change_flags+0x1c/0x58
netif_change_flags from dev_change_flags+0x38/0xa0
dev_change_flags from ip_auto_config+0x2c4/0x11f0
ip_auto_config from do_one_initcall+0x58/0x200
do_one_initcall from kernel_init_freeable+0x1cc/0x238
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x38
[... TRIM...]
Standardize the error handling by making the function return NULL on
all error conditions. The API is used in just the netcp_core.c so the
impact is limited.
Note, this change, in effect reverts commit 5b6cb43b4d62 ("net:
ethernet: ti: netcp_core: return error while dma channel open issue"),
but provides a less error prone implementation. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: storage: Fix memory leak in USB bulk transport
A kernel memory leak was identified by the 'ioctl_sg01' test from Linux
Test Project (LTP). The following bytes were mainly observed: 0x53425355.
When USB storage devices incorrectly skip the data phase with status data,
the code extracts/validates the CSW from the sg buffer, but fails to clear
it afterwards. This leaves status protocol data in srb's transfer buffer,
such as the US_BULK_CS_SIGN 'USBS' signature observed here. Thus, this can
lead to USB protocols leaks to user space through SCSI generic (/dev/sg*)
interfaces, such as the one seen here when the LTP test requested 512 KiB.
Fix the leak by zeroing the CSW data in srb's transfer buffer immediately
after the validation of devices that skip data phase.
Note: Differently from CVE-2018-1000204, which fixed a big leak by zero-
ing pages at allocation time, this leak occurs after allocation, when USB
protocol data is written to already-allocated sg pages. |
| In the Linux kernel, the following vulnerability has been resolved:
udp_tunnel: use netdev_warn() instead of netdev_WARN()
netdev_WARN() uses WARN/WARN_ON to print a backtrace along with
file and line information. In this case, udp_tunnel_nic_register()
returning an error is just a failed operation, not a kernel bug.
udp_tunnel_nic_register() can fail due to a memory allocation
failure (kzalloc() or udp_tunnel_nic_alloc()).
This is a normal runtime error and not a kernel bug.
Replace netdev_WARN() with netdev_warn() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: aspeed - fix double free caused by devm
The clock obtained via devm_clk_get_enabled() is automatically managed
by devres and will be disabled and freed on driver detach. Manually
calling clk_disable_unprepare() in error path and remove function
causes double free.
Remove the manual clock cleanup in both aspeed_acry_probe()'s error
path and aspeed_acry_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Don't overflow during division for dirty tracking
If pgshift is 63 then BITS_PER_TYPE(*bitmap->bitmap) * pgsize will overflow
to 0 and this triggers divide by 0.
In this case the index should just be 0, so reorganize things to divide
by shift and avoid hitting any overflows. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix NULL-deref on snapshot tear down
In case of early initialisation errors and on platforms that do not use
the DPU controller, the deinitilisation code can be called with the kms
pointer set to NULL.
Patchwork: https://patchwork.freedesktop.org/patch/525099/ |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
The MBHC resources must be released on component probe failure and
removal so can not be tied to the lifetime of the component device.
This is specifically needed to allow probe deferrals of the sound card
which otherwise fails when reprobing the codec component:
snd-sc8280xp sound: ASoC: failed to instantiate card -517
genirq: Flags mismatch irq 299. 00002001 (mbhc sw intr) vs. 00002001 (mbhc sw intr)
wcd938x_codec audio-codec: Failed to request mbhc interrupts -16
wcd938x_codec audio-codec: mbhc initialization failed
wcd938x_codec audio-codec: ASoC: error at snd_soc_component_probe on audio-codec: -16
snd-sc8280xp sound: ASoC: failed to instantiate card -16 |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: reject negative ifindex
Recent changes in net-next (commit 759ab1edb56c ("net: store netdevs
in an xarray")) refactored the handling of pre-assigned ifindexes
and let syzbot surface a latent problem in ovs. ovs does not validate
ifindex, making it possible to create netdev ports with negative
ifindex values. It's easy to repro with YNL:
$ ./cli.py --spec netlink/specs/ovs_datapath.yaml \
--do new \
--json '{"upcall-pid": 1, "name":"my-dp"}'
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
$ ip link show
-65536: some-port0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 7a:48:21:ad:0b:fb brd ff:ff:ff:ff:ff:ff
...
Validate the inputs. Now the second command correctly returns:
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
lib.ynl.NlError: Netlink error: Numerical result out of range
nl_len = 108 (92) nl_flags = 0x300 nl_type = 2
error: -34 extack: {'msg': 'integer out of range', 'unknown': [[type:4 len:36] b'\x0c\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0c\x00\x03\x00\xff\xff\xff\x7f\x00\x00\x00\x00\x08\x00\x01\x00\x08\x00\x00\x00'], 'bad-attr': '.ifindex'}
Accept 0 since it used to be silently ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-core: fix memory leak in dhchap_secret_store
Free dhchap_secret in nvme_ctrl_dhchap_secret_store() before we return
fix following kmemleack:-
unreferenced object 0xffff8886376ea800 (size 64):
comm "check", pid 22048, jiffies 4344316705 (age 92.199s)
hex dump (first 32 bytes):
44 48 48 43 2d 31 3a 30 30 3a 6e 78 72 35 4b 67 DHHC-1:00:nxr5Kg
75 58 34 75 6f 41 78 73 4a 61 34 63 2f 68 75 4c uX4uoAxsJa4c/huL
backtrace:
[<0000000030ce5d4b>] __kmalloc+0x4b/0x130
[<000000009be1cdc1>] nvme_ctrl_dhchap_secret_store+0x8f/0x160 [nvme_core]
[<00000000ac06c96a>] kernfs_fop_write_iter+0x12b/0x1c0
[<00000000437e7ced>] vfs_write+0x2ba/0x3c0
[<00000000f9491baf>] ksys_write+0x5f/0xe0
[<000000001c46513d>] do_syscall_64+0x3b/0x90
[<00000000ecf348fe>] entry_SYSCALL_64_after_hwframe+0x72/0xdc
unreferenced object 0xffff8886376eaf00 (size 64):
comm "check", pid 22048, jiffies 4344316736 (age 92.168s)
hex dump (first 32 bytes):
44 48 48 43 2d 31 3a 30 30 3a 6e 78 72 35 4b 67 DHHC-1:00:nxr5Kg
75 58 34 75 6f 41 78 73 4a 61 34 63 2f 68 75 4c uX4uoAxsJa4c/huL
backtrace:
[<0000000030ce5d4b>] __kmalloc+0x4b/0x130
[<000000009be1cdc1>] nvme_ctrl_dhchap_secret_store+0x8f/0x160 [nvme_core]
[<00000000ac06c96a>] kernfs_fop_write_iter+0x12b/0x1c0
[<00000000437e7ced>] vfs_write+0x2ba/0x3c0
[<00000000f9491baf>] ksys_write+0x5f/0xe0
[<000000001c46513d>] do_syscall_64+0x3b/0x90
[<00000000ecf348fe>] entry_SYSCALL_64_after_hwframe+0x72/0xdc |
| In the Linux kernel, the following vulnerability has been resolved:
codetag: debug: handle existing CODETAG_EMPTY in mark_objexts_empty for slabobj_ext
When alloc_slab_obj_exts() fails and then later succeeds in allocating a
slab extension vector, it calls handle_failed_objexts_alloc() to mark all
objects in the vector as empty. As a result all objects in this slab
(slabA) will have their extensions set to CODETAG_EMPTY.
Later on if this slabA is used to allocate a slabobj_ext vector for
another slab (slabB), we end up with the slabB->obj_exts pointing to a
slabobj_ext vector that itself has a non-NULL slabobj_ext equal to
CODETAG_EMPTY. When slabB gets freed, free_slab_obj_exts() is called to
free slabB->obj_exts vector.
free_slab_obj_exts() calls mark_objexts_empty(slabB->obj_exts) which will
generate a warning because it expects slabobj_ext vectors to have a NULL
obj_ext, not CODETAG_EMPTY.
Modify mark_objexts_empty() to skip the warning and setting the obj_ext
value if it's already set to CODETAG_EMPTY.
To quickly detect this WARN, I modified the code from
WARN_ON(slab_exts[offs].ref.ct) to BUG_ON(slab_exts[offs].ref.ct == 1);
We then obtained this message:
[21630.898561] ------------[ cut here ]------------
[21630.898596] kernel BUG at mm/slub.c:2050!
[21630.898611] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
[21630.900372] Modules linked in: squashfs isofs vfio_iommu_type1
vhost_vsock vfio vhost_net vmw_vsock_virtio_transport_common vhost tap
vhost_iotlb iommufd vsock binfmt_misc nfsv3 nfs_acl nfs lockd grace
netfs tls rds dns_resolver tun brd overlay ntfs3 exfat btrfs
blake2b_generic xor xor_neon raid6_pq loop sctp ip6_udp_tunnel
udp_tunnel nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib
nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct
nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4
nf_tables rfkill ip_set sunrpc vfat fat joydev sg sch_fq_codel nfnetlink
virtio_gpu sr_mod cdrom drm_client_lib virtio_dma_buf drm_shmem_helper
drm_kms_helper drm ghash_ce backlight virtio_net virtio_blk virtio_scsi
net_failover virtio_console failover virtio_mmio dm_mirror
dm_region_hash dm_log dm_multipath dm_mod fuse i2c_dev virtio_pci
virtio_pci_legacy_dev virtio_pci_modern_dev virtio virtio_ring autofs4
aes_neon_bs aes_ce_blk [last unloaded: hwpoison_inject]
[21630.909177] CPU: 3 UID: 0 PID: 3787 Comm: kylin-process-m Kdump:
loaded Tainted: G W 6.18.0-rc1+ #74 PREEMPT(voluntary)
[21630.910495] Tainted: [W]=WARN
[21630.910867] Hardware name: QEMU KVM Virtual Machine, BIOS unknown
2/2/2022
[21630.911625] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS
BTYPE=--)
[21630.912392] pc : __free_slab+0x228/0x250
[21630.912868] lr : __free_slab+0x18c/0x250[21630.913334] sp :
ffff8000a02f73e0
[21630.913830] x29: ffff8000a02f73e0 x28: fffffdffc43fc800 x27:
ffff0000c0011c40
[21630.914677] x26: ffff0000c000cac0 x25: ffff00010fe5e5f0 x24:
ffff000102199b40
[21630.915469] x23: 0000000000000003 x22: 0000000000000003 x21:
ffff0000c0011c40
[21630.916259] x20: fffffdffc4086600 x19: fffffdffc43fc800 x18:
0000000000000000
[21630.917048] x17: 0000000000000000 x16: 0000000000000000 x15:
0000000000000000
[21630.917837] x14: 0000000000000000 x13: 0000000000000000 x12:
ffff70001405ee66
[21630.918640] x11: 1ffff0001405ee65 x10: ffff70001405ee65 x9 :
ffff800080a295dc
[21630.919442] x8 : ffff8000a02f7330 x7 : 0000000000000000 x6 :
0000000000003000
[21630.920232] x5 : 0000000024924925 x4 : 0000000000000001 x3 :
0000000000000007
[21630.921021] x2 : 0000000000001b40 x1 : 000000000000001f x0 :
0000000000000001
[21630.921810] Call trace:
[21630.922130] __free_slab+0x228/0x250 (P)
[21630.922669] free_slab+0x38/0x118
[21630.923079] free_to_partial_list+0x1d4/0x340
[21630.923591] __slab_free+0x24c/0x348
[21630.924024] ___cache_free+0xf0/0x110
[21630.924468] qlist_free_all+0x78/0x130
[21630.924922] kasan_quarantine_reduce+0x11
---truncated--- |
